How to Determine if You Have Hard Water

Co-authored by Anthony "TC" Williams

Last Updated: February 26, 2020 References Approved

Hard water contains minerals, usually calcium and magnesium ions, which make soap less effective and leave scale on your dishes and plumbing. There are several tests for water hardness, ranging from an easy one you can try immediately to a more accurate test kit. If it turns out you do have hard water, there are several approaches you can take to minimize the effects.

Method 1

Method 1 of 3:

Testing for Hardness Quickly

1
Choose a clear bottle. This test will only give a very rough estimate of water hardness, but it only takes a few minutes. Start with a bottle that can hold at least 12 ounce (360 mL), and preferably more. If you can't find a bottle with a cap, use any clear container.^{[1]
X
Research source}
2
Fill the bottle with water. Measure 12 ounces (360 mL) of your tap water and pour it into the container.

Advertisement
3
Add ten drops of liquid soap to the container. Some soaps react to hard water more than others, which is one reason this test isn't always accurate. Many dishwashing detergents do not react much to hard water, so it may be best to use liquid hand soap for this test.^{[2]
X
Research source} Castile soap is a common choice, since its simple ingredient list ensures that other chemicals are not interfering with the results.^{[3]
X
Research source}^{[4]
X
Research source}
4
Shake the bottle. Cap the bottle and shake it for a few seconds. If your container doesn't have a cap, stir vigorously until the soap is thoroughly mixed into the water.
5
Look for suds. Open the bottle and look for suds at the top of the water. If there are plenty of suds, your water is probably quite soft.^{[5]
X
Research source} If there are only a few bubbles, move on to the next step.
6
Gradually shake in more soap. Add more soap five or ten drops at a time, shaking the bottle after each batch. The number of drops it takes to make suds will give you a rough estimate of your water hardness:^{[6]
X
Research source}
- 20 drops: slightly hard
- 30 drops: moderately hard
- 40 drops: hard
- 50+ drops: very hard
7
Look for soap scum. Completely soft water creates foam at the surface, but leaves the water itself clear. The minerals in hard water react with soap to create "soap scum." Besides reducing foam, this scum makes the water look cloudy. If you water is thick with soap scum, your water is almost certainly hard.
8
Decide whether to soften your water. A result of "moderately hard" or below typically won't cause major problems in your household.^{[7]
X
Trustworthy Source
Penn State Extension
Educational organization dedicated to delivering science-based information to people, businesses, and communities
Go to source} If your water doesn't seem too hard but you are noticing problems, read below for DIY solutions or more accurate tests.

Method 2

Method 2 of 3:

Recognizing and Solving Water Hardness Problems

1
Check for white scale. The minerals in hard water can leave a white scale on your sink, shower, or bathtub. If it's happening there, it's probably happening in your pipes as well. This is one problem with no do-it-yourself fix, and probably requires installing a water softener. If left alone, the hard water will slowly clog your pipes, reducing water pressure and shortening the lifespan of your plumbing.^{[8]
X
Research source} If the scale is minor and your pipes seem to function fine, however, you may want to solve specific problems using the cheap solutions below.
2
Examine your laundry. The soap scum that forms in hard water can cling to fabric, leaving it stiff and rough. In severe cases, it can fail to clean the clothes completely, making white fabric grey and bright colors dull, or even leaving a sour odor on the clothes.^{[9]
X
Research source} Try one or more of the following solutions:^{[10]
X
Research source}
- Increase the washing machine temperature.
- Use more detergent.
- Add non-precipitating water conditioner to your machine before the detergent.
3
Look for spots and etching on your glassware. One obvious sign of hard water is white spots on your glasses after washing. There are actually two types of damage that hard water can cause:^{[11]
X
Research source}
- Hard water spots are surface stains that you can remove by scrubbing with vinegar or an abrasive cleaner such as baking powder.
- "Etching" permanently damages the glass, although you may be able to buff it out with a glass polishing kit. Mild etching looks like a rainbow film, while severe etching turns the glass opaque.
- To reduce the chance of either type of damage, reduce the temperature of the dishwasher or rinse your dishes more thoroughly before loading the machine.
4
Deal with shower problems. Particularly hard water may irritate skin, leave hair stiff and dull, or even leave a filmy soap residue on your skin. If you don't want to install a household water softener system, try these fixes:
- Install a showerhead water softener and replenish it occasionally by adding salt. (Showerhead "softeners" that don't need salt are actually filters, and will not soften your water.)
- To improve your hair texture, use a chelating shampoo once a week, followed by a moisturizing conditioner. Chelating shampoos are supposed to strip minerals from your hair, and typically contain the ingredient "EDTA" (ethylenediaminetetraacetic acid).^{[12]
  X
  Research source}

Method 3

Method 3 of 3:

Checking Hardness Levels Accurately

1
Understand water hardness units. An official report or a scientific test should give you a precise measurement. These are the most common units in most regions, so learn how to interpret the results:^{[13]
X
Research source}
- Grains Per Gallon (or just "grains"): 3.5 – 7.0 means moderately hard. Anything higher will likely cause problems.
- ppm, mg/L, or American degree of hardness: 60–120 means moderately hard.
2
Contact your local water company. Your water provider may be able to tell you the hardness of your water supply.^{[14]
X
Research source}
3
Ask a water softener company for a free test. Many of these companies offer a free water test, hoping you'll use their services. They may request a water sample and send back the results, or they may send a water hardness test to your home. Keep reading for instructions on how to use the test.
4
Test your water with a test strip. You can buy these test strips online or where water softeners are sold. These are very simple to use: just dip a test strip in your water and watch it change color. The test strip label or an accompanying guide should tell you how hard your water is based on the color.
- This is accurate enough for a household, but don't rely on it to make fine adjustments to a pool or other system that requires a specific hardness level.^{[15]
  X
  Research source}
5
Test with a water hardness titration kit. This more accurate test is available online or at some pool stores. Typically you fill a small bottle with water up to the mark on the side, then add a chemical from the kit drop by drop. The number of drops it takes to cause a color change will tell you the hardness of your water.
- Other types of test with a digital display are typically intended for special situations, such as extremely soft water. These are more expensive and not necessary for household testing.^{[16]
  X
  Research source}
6
Send your water to a professional water testing lab. Consider this more expensive option only if you need a detailed analysis of your water, including contaminants and exact minerals. If you have a well or other private water source, it's a good idea to have a sample tested at least once a year, although testing for contamination is more important than water hardness.^{[17]
X
Research source} You may also want your water tested if you run a spa or other business that relies on clean water.
- If you're not sure how to find a lab that can test your water, ask for advice at a university agricultural extension.

Expert Q&A

Question

What chemical can be used to test total hardness in place of EDTA ?

Anthony "TC" Williams
Experienced Landscaper
Anthony "TC" Williams is a Professional Landscaper in Idaho. He is the President and Founder of Aqua Conservation Landscape & Irrigation, an Idaho Registered Landscape Business Entity. With over 21 years of landscaping experience, TC has worked on projects such as the Idaho Botanical Garden in Boise, Idaho. He is a Idaho Registered Contractor and a previously Licensed Irrigator in the State of Texas.

Anthony "TC" Williams

Experienced Landscaper

Expert Answer

In the absence of EDTA, denatured alcohol can be used to test the total hardness of water.
Question

My tub faucet and handles have a white film on them. Is this hard water buildup?

Anthony "TC" Williams
Experienced Landscaper
Anthony "TC" Williams is a Professional Landscaper in Idaho. He is the President and Founder of Aqua Conservation Landscape & Irrigation, an Idaho Registered Landscape Business Entity. With over 21 years of landscaping experience, TC has worked on projects such as the Idaho Botanical Garden in Boise, Idaho. He is a Idaho Registered Contractor and a previously Licensed Irrigator in the State of Texas.

Anthony "TC" Williams

Experienced Landscaper

Expert Answer

White film on your tub's faucet and handles most likely points to hard water buildup, but don't rule out soap residue as being a factor.
Question

Will hard water make skin break out?

Community Answer

Showering in hard water can clog the pores and irritate the skin, which could certainly cause breakouts.

Warnings

Some water softening systems can have serious health risks for people who are on medically necessary low-sodium diets.^{[19]
X
Trustworthy Source
Penn State Extension
Educational organization dedicated to delivering science-based information to people, businesses, and communities
Go to source} If you are on any special diet to regulate mineral intake, ask your doctor for more information before connecting a water softener to a faucet you drink from.

⧼thumbs_response⧽
Helpful 1 Not Helpful 1
Don't put too much faith in maps that show areas of water hardness across a whole country or region. These only tell you the average hardness in your area, which may not match your local conditions.^{[20]
X
Research source}

⧼thumbs_response⧽
Helpful 1 Not Helpful 1