X
wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 11 people, some anonymous, worked to edit and improve it over time.
wikiHow marks an article as reader-approved once it receives enough positive feedback. In this case, 91% of readers who voted found the article helpful, earning it our reader-approved status.
This article has been viewed 133,541 times.
Learn more...
This article explains how to quickly and cheaply make a 5 foot (1.5 m) Christmas star to put the exclamation point on your Christmas light display.
Steps
-
1Gather the parts. You will need: 3 - 10' sections of 1/2" plastic conduit, 10 - 1/4" X 3" galvanized bolts, 10 1/4" galvanized fender washers, 10 1/4" lock washers, 10 1/4" galvanized nuts, 2 strings or more of 100 count mini lights, plastic ties or electrical tape.
-
2Cut the conduit in half so you have 6–5 feet (1.8–1.5 m) tubes.Advertisement
-
3Drill a 3/8" hole through one end of 5 pieces of conduit 1" from one end
-
4Bolt two pieces of conduit together using the 3" bolt. With the bolt through the conduit slide the fender washer on followed by the lock washer then the nut. Finger tighten.
-
5Lay this "V" onto the ground and lay the drilled end of another 5 feet (1.5 m) section on the one end of the "V". You are now forming the star. Drill through the pre-drilled conduit into the undrilled conduit. You do it this way to make sure the holes line up and the bolt will fit through. With the bolt through the conduit slide the fender washer on followed by the lock washer then the nut. Finger tighten.
-
6Continue with the remaining 2 pieces of conduit until you have bolted all five corners of the star together. The star will have play in it so shape the star until you are happy with the way it looks.
-
7Notice that you have 5 points inside the star where the conduit crosses. Drill these spots and bolt them one by one so that your star holds its shape.
-
8Wrap the star with the lights. Keep in mind that there are 10 pieces of the star that need to be wrapped. (5 on each side) if you put Twenty lights on each side, your star will be uniformly lit. Attached the lights using electrical tape and/or plastic tie wraps.
-
9To gain height, you can put a 10 feet (3.0 m) 1/2" metal conduit a foot inside a 10 feet (3.0 m) 3/4" metal conduit. Drill a hole though both pieces of conduit and secure with a cotter pin. Your pole should now be about 19 feet (5.8 m) long. Drill another hole one inch down from the end of the 1/2" conduit. Replace the top bolt on the star with a 4.5" bolt and run the bolt through the conduit to secure it in place. Mount the pole to a chimney, tree, playhouse, wall or whatever you have to put your star in the sky! Have fun!
Advertisement
Community Q&A
-
QuestionIf I go to a 6' measurement for a star, will it come out the same as a 5' star?
DonaganTop AnswererThe shape will be the same. The size will be about 20% larger. -
QuestionWhat's the perimeter of the 5-foot star? How many feet of lights do I need?DonaganTop AnswererThe perimeter is roughly 20 feet. That's how much lighting you'll need if you simply run the lights along the perimeter. If you wind the lights along the perimeter, you'll need more, depending on how "tight" the winding is.
-
QuestionHow do I make a big star without metal?
RevadCommunity AnswerYou could cut the star shape out of heavy cardboard and wrap in foil for a silver star, or get a gold metallic paper to wrap for gold star.
Advertisement
Warnings
- Do not use metal conduit for the star as it conducts electricity and could be a hazard.⧼thumbs_response⧽
Advertisement
About This Article
Advertisement
