How to Make a Burning Laser

Lasers have fascinated people for years. They bring to mind both science fiction and science fact, making them a lot of fun to play with. Low powered laser pointers are commonplace as classroom tools or pet toys, but if you get the right diode you can construct and focus a laser that is powerful enough to burn through objects or set them on fire. That said, such a laser can be dangerous and should not be taken lightly.

Part 1
Part 1 of 3:

Obtaining a Diode

  1. Image titled Make a Burning Laser Step 1
    1
    Select a diode strength and color. The strength of a diode will be listed in milliwatts (mW). The color of the diode will be determined by its wavelength (measured in nanometers, nm). A wavelength of 650 nm corresponds to a red laser, a wavelength of 405 nm corresponds to a blue laser, and a green laser has a wavelength around 520 nm. Green lasers are the most expensive, followed by blue. Red is the cheapest.[1]
    • You can buy diodes online and sometimes at electronic supply stores. The diode costs can range anywhere from tens to thousands of dollars, depending on the laser you choose.
  2. Image titled Make a Burning Laser Step 2
    2
    Take apart an old DVD or Blu-Ray disk burner. If you aren't picky about the color, you can take apart an old DVD or Blu-Ray disk burner. There will be two diodes. Find the diode on the disk burning side. The one on the disk reading side is not strong enough to produce a burning laser.[2]
    • The diode will look like a small round light. It is likely encased in metal and will be positioned so that it can shine on the bottom of the DVD/Blu-Ray tray.
    Advertisement
  3. Image titled Make a Burning Laser Step 3
    3
    Salvage the diode from the disk burner. Once you have located the disk burning diode, remove it from the DVD (or Blu-Ray) burner. You may have to remove small screws or cut the diode away from the rest of the burner. It is possible that the diode is encased in a metal casing. If this is the case, the casing can be left on the diode after you remove it.
    4. Advertisement
Part 2
Part 2 of 3:

Constructing the Laser

  1. Image titled Make a Burning Laser Step 4
    1
    Connect the diode to a laser driver. The laser driver is the electrical component that controls the functioning of the laser. The diode will likely need soldered to the laser driver. There should be two leads coming from the diode for this purpose. Use a soldering gun to solder the leads to the driver at the positive and negative terminals. These terminals should be labeled on the driver and extend to the edge of the driver for soldering purposes.[3]
    • The driver should not be connected to any power source until soldering is complete.
  2. Image titled Make a Burning Laser Step 5
    2
    Power the laser with batteries. After the diode has been connected to the driver, you can connect the driver to a power source. Batteries are the go to choice since they make your laser portable. You will need at least AA batteries to produce a burning laser.[4]
    • The driver will have leads for a power supply. These leads will need to be connected to a battery pack or directly to the battery. If the leads need soldered, you will have to use a battery pack. You cannot solder onto a battery.
  3. Image titled Make a Burning Laser Step 6
    3
    Encase the laser. You can buy a laser casing online to house the parts of your laser. Alternatively, you can make a laser casing from things lying around your house. Popular items used to make casings include Altos mint cans, bic lighters, and the casings of weaker laser pointers.
    4. Advertisement
Part 3
Part 3 of 3:

Focusing the Laser

  1. Image titled Make a Burning Laser Step 7
    1
    Obtain a laser lens. A laser lens is needed to condense the light from a wide pattern to a thin beam. This concentrates the energy of your laser. This concentrated beam is what allows you to burn things with your laser.[5]
    • Glass lenses are better than plastic lenses, but they are more expensive.
  2. Image titled Make a Burning Laser Step 8
    2
    Concentrate the beam. Adjust the lens to concentrate the beam when you are using the laser. This will make the beam powerful enough to burn through some materials and ignite matches or paper. Be very careful when using this laser. Do not point it at anyone or anything that does not belong to you. The laser is very dangerous when focused.[6]
    • It is a crime to point the laser at aircraft and/or motor vehicles.
  3. Image titled Make a Burning Laser Step 9
    3
    Widen the beam when you are finished. Adjust the beam so that the laser is spread out. This will make the laser less powerful when hitting any one spot. This is the safest way to store the laser in case it accidentally gets turned on. Keep in mind that the laser can still be dangerous, however. It should never be within reach of children.
    4. Advertisement

Community Q&A

  • Question
    Can I use the laser from a DVD player?
    Community Answer
    Community Answer
    No, a DVD reader laser is not powerful enough to burn. However, it would make a simple, fun pet laser pointer.
  • Question
    How big does the flashlight have to be?
    Community Answer
    Community Answer
    This depends on your Aziz laser housings size and the average would be a medium sized flashlight that could fit an AA battery.
  • Question
    Can a burning laser light a candle?
    Community Answer
    Community Answer
    It depends on how powerful the laser itself is. If you can make smoke from a laser, it can light a candle.
Advertisement

Warnings

Advertisement

You Might Also Like

Make a Simple Electrical Circuit
How to
Make a Simple Electrical Circuit
Build an EMP Generator
How to
Build an EMP Generator
Make a Simple Electric Generator
How to
Make a Simple Electric Generator
Convert AC to DC
How to
Convert AC to DC
How to
Make a Light out of Batteries
Use a Multimeter
How to
Use a Multimeter
Build a Motor
How to
Build a Motor
Make a Tesla Coil
How to
Make a Tesla Coil
Remember Electrical Resistor Color Codes
How to
Remember Electrical Resistor Color Codes
Install a Junction Box
How to
Install a Junction Box
Make an Engine from a Battery, Wire and a Magnet
How to
Make an Engine from a Battery, Wire and a Magnet
Build a Simple Electric MotorSimple Electric Motor Project: Materials & Instructions
Build a Fuel Cell
How to
Build a Fuel Cell
Make a Simple One‐Direction Electric Toy Car
How to
Make a Simple One‐Direction Electric Toy Car
Advertisement

References

  1. ↑ https://lasertoolsco.com/2017/04/05/different-laser-colors-and-their-corresponding-function/
  2. ↑ https://hackaday.com/2016/04/18/sciencing-dvd-rw-laser-diodes/
  3. ↑ https://www.teamwavelength.com/laser-diode-driver-basics/
  4. ↑ https://www.youtube.com/watch?v=v6SLhk9SNbw
  5. ↑ https://endurancelasers.com/laser-beam-focusing/
  6. ↑ https://endurancelasers.com/laser-beam-focusing/

About This Article

wikiHow Staff
Co-authored by:
wikiHow Staff
wikiHow Staff Writer
This article was co-authored by wikiHow Staff. Our trained team of editors and researchers validate articles for accuracy and comprehensiveness. wikiHow's Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards. This article has been viewed 139,880 times.
116 votes - 86%
Co-authors: 23
Updated: October 8, 2022
Views: 139,880
Categories: Electrical Projects | Optical Devices
Advertisement