Walking on stilts is a fun pastime! With a few easy steps, you can make yourself a beginner set of stilts in less than 30 minutes.

Steps

  1. 1
    Determine how much height you would like to gain on your stilts. One foot (about 30.5 cm)is recommended for beginners. [Note: it is not recommended it gain more than three feet, both because it is difficult to get on stilts at this height and because a larger secure base would have to be constructed for support.]
  2. 2
    In the standing position, have someone measure the distance from the bottom of your foot to your elbow.
    Advertisement
  3. 3
    Add the measurements from #1 and #2 together. This will be the length of your stilt poles.
  4. 4
    Make the stilt poles: Cut the 2”x2” board into two pieces which are each the length determined in #3. Be cautious to cut the ends so at least one end on each pole (the bottom) is flat, as this will be the surface on which you will be walking.
  5. 5
    Make the footholds: Cut another 2”x2” piece to a length that exceeds the width of your foot by 1”. A good size is usually 4”-6”. Again, insure that at least one side on each piece is flat, as this side will line up with the long stilt poles.
  6. 6
    Make the foothold supports: Cut the 2”x4”x4” board into triangles such that two sides of each triangle are 4” long (the hypotenuse is therefore longer than 4”).
  7. 7
    Nail these triangle footholds into the 2”x2” stilt poles. You will want to measure to make sure you are nailing these pieces in at the right height. From the bottom of the stilt poles, measure the height you want to gain (from #1) and subtract 2”. This will be where you nail in the top of the triangle, so that one of the 4” surfaces is perpendicular to the stilt pole and the other is parallel to the stilt pole. Two nails should be used to secure each triangle. Hammer one nail in through the bottom of the triangle (1” from the bottom) through the stilt pole first. Hammer the other about 1” above that through the triangle first.
  8. 8
    Take the footholds and place each perpendicular to the stilt pole on top of the triangle foothold support for each stilt. The foothold should fit nicely on top of the triangle. Make sure the flat side of the foothold is next to the stilt pole. To fix the foothold into place, nail the footholds into both the 2”x2” stilt pole and the foothold supports. Three nails should be hammered in through the top of the foothold, at a 45 degree angle to the foothold, through the support and stilt pole.
  9. 9
    If any of the nails are too long, hammer them so that the point faces downward, so as to avoid injury if you fall off the stilts.
  10. 10
    Sand down any rough spots on the top of the boards or on the hand holds to make the stilts more comfortable to grip.
  11. 11
    Voila! You can now try to walk on your stilts! Happy walking!
  12. Advertisement

Community Q&A

  • Question
    How exactly do I get onto my stilts?
    Kicky Ricky
    Kicky Ricky
    Community Answer
    First times are difficult, and it depends on your balancing skills. First, step on one stilt and then quickly step onto another. The point is that you hold the footholds attached to your feet with upward force and control the stick with your hand.
Advertisement

Warnings

  • Walking on stilts can be hazardous to your health and safety. Please ensure that your stilts are secure and stable before putting your full body weight on them. This set of stilts will not be safe for those over 250 lbs.
    ⧼thumbs_response⧽
Advertisement

Things You'll Need

  • Hammer
  • 10- Nails (3”)
  • 10’minimum- 2”x2” board
  • 2- 2”x4”x4” boards
  • Sandpaper

About This Article

wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 14 people, some anonymous, worked to edit and improve it over time. This article has been viewed 116,159 times.
106 votes - 85%
Co-authors: 14
Updated: December 27, 2021
Views: 116,159
Categories: Performing Arts
Advertisement