How to Load a Shotgun

Last Updated: January 21, 2020 References

Shotguns are popular around the world for hunting, shooting sports and home defense. They fire shells of metal shot that are usually loaded one at a time, instead of in a clip. While shotgun technology has advanced over the years, loading most shotguns is still a simple task.

Method 1

Method 1 of 2:

Loading a Pump-Action Shotgun

1
Make sure the safety is on, the chamber unloaded, and the barrel pointed away from you in a safe direction. This is always the first step when loading or handling any gun. Consult your weapon's instruction manual to locate the safety feature.^{[1]
X
Research source}
2
Determine what gauge (bore diameter) your shotgun is so you can select the right size shells. Common shotgun sizes are 10, 12, 16, 20, .410 bore, and 28. Shotshell of one gauge may be fired in a shotgun of another gauge, but doing so requires a special tube. Otherwise it is best to just select the proper sized ammo for your weapon.^{[2]
X
Research source}

Advertisement
3
Place the butt of the stock on your left thigh while sitting. You can also secure the stock under your arm with the gun turned sideways. Make sure that the trigger and trigger guard are positioned on the side of the shotgun facing away from you.^{[3]
X
Research source}
4
Place a single shell against the loading flap just ahead of the trigger guard. The "business end" of the shell should be pointing toward the end of the gun barrel. The business end is the end of the shell that the shot comes out of and is opposite the metal capped end of the shell where the explosive charge is housed.^{[4]
X
Research source}
5
Using your thumb, push the shell straight up into the loading flap until you hear and feel a distinct click. When it clicks, the rim of the shell should have passed the magazine catch.^{[5]
X
Research source}
6
Repeat until the magazine tube is full. You can tell the tube is full when you attempt to load a shell but it won't go in.^{[6]
X
Research source}
7
Hold in the action release button and pump the slide backwards and then forwards with a reasonable amount of force to load the chamber. This will strip a shell from the magazine and load it into firing position. The shotgun is now ready to fire.^{[7]
X
Research source}

Method 2

Method 2 of 2:

Loading a Break-Action Shotgun

1
Make sure the safety is on and the gun pointed away from you in a safe direction. Always treat a gun as though it were loaded, even if you know it isn't.^{[8]
X
Research source}
2
Find and engage the barrel breach lever, latch or button. This will usually be on the right side of the gun, where the barrel meets the stock.^{[9]
X
Research source}
- Unlike a pump-action shotgun, a break action has no magazine tube to load several shells at a time into. Instead, the gun breaks open to allow you to load a shell directly into the chamber of your barrel (or barrels). This means your gun needs to be reloaded after every shot, or every two shots if you have a double-barreled shotgun.
3
Open the break-action and lower the barrel away from the body of the shotgun.^{[10]
X
Research source}
4
Remove and discard any spent casings. Be careful: these may be hot if the gun was recently fired. Try not to let your hand touch the metal of the barrel.^{[11]
X
Research source}
5
Replace each used casing with a fresh shell. The business-end of the shell should slide into the barrel.^{[12]
X
Research source}
6
Bring the barrel back up and close the break until you hear and feel it click. Your gun is now loaded and ready to fire.^{[13]
X
Research source}

Community Q&A

Question

Does a shotgun have to be loaded to put the safety on?

Community Answer

You can put the safety on regardless of whether or not the gun is loaded.
Question

How do I remove shells?

Community Answer

Depending on the make, put the gun on safe and act as if you were putting another round in with the slide, it should pop free.
Question

Do I need to hold the action release button every time I pump the slide?

vivek rathore

Community Answer

No. The action bar will not slide back if the weapon has not been discharged without pressing and holding the release button located near the trigger guard. Push and hold the release and slowly pull the action bar back, but not all the way. Stop right before the end of the pull. If there is a round in the chamber it will pop out; simply remove it. If there is another round in the magazine tube, it will pop onto the carrier.

Warnings

Never attempt to force a shotshell into the magazine with any object such as a screwdriver. You could accidentally set off the shell, seriously injuring yourself or others.

⧼thumbs_response⧽
Helpful 19 Not Helpful 3
Never attempt to 'mismatch' firearms and ammunition, the round may fit in the chamber, but it could be of a considerably higher power than your gun is designed to handle. Your gun could explode and harm or kill you or other bystanders.

⧼thumbs_response⧽
Helpful 13 Not Helpful 5
Guns are not toys! Firearms should be treated with respect and never handled by children without adult supervision.

⧼thumbs_response⧽
Helpful 12 Not Helpful 5