How to Lay a Block Wall with Cement or Cinder Blocks

Build a retaining wall with this easy-to-follow guide

Co-authored by Gerber Ortiz-Vega and Hannah Madden

Last Updated: November 28, 2022 References Approved

Pouring the Footing

|

Laying Concrete Blocks with Mortar

|

Expert Q&A

|

Warnings

|

Things You'll Need

Are you starting the foundation for a large structure or building a retaining wall? If so, you’re probably preparing to lay some concrete blocks. Laying concrete blocks is a simple project, even for beginner DIYers. In this article, we’ll walk you through the entire process, including what tools you need and what type of blocks to get. To start your project today, read on.

Things You Should Know

Before laying cinder blocks, pour a footing below the frost line. The footing is the foundation for the concrete blocks.
Let your footing dry for at least 3 days before laying concrete blocks. Start with corner blocks, and use mortar to keep them in place.
Place a wooden stake in each corner of the footing, and use a string line wrapped around the stakes to make sure your blocks are straight.
Stack the blocks on top of each other in an alternating pattern on top of the footing. Apply mortar to the sides of each block before stacking them.

Part 1

Part 1 of 2:

Pouring the Footing

1
Dig below the frost line. The footing is the solid concrete perimeter that your concrete blocks will sit on. Check with your county to see how far down the frost line is, then dig beneath that line to start your footing.^{[1]
X
Research source}
- Be sure you’re not going to dig through a utility line as you start your project. In the United States, call 811 to see which utility lines are on your property.
- Your local building codes may also specify how deep the footing needs to go. Typically, you need to make your footing twice as deep as the thickness of the wall.
2
Make your footing twice as wide as your concrete blocks. If you're using standard blocks, which are 8 in (20 cm), make your footing at least 16 in (41 cm) wide. Dig the perimeter where your concrete wall is going to go that’s at least twice as wide as your blocks.^{[2]
X
Research source}
- To ensure you’re digging in a straight line, snap a chalk line onto the ground to create your base shape.
Advertisement
3
Place 2x4s in the hole to keep the concrete in place. Grab eight 2x4s and place them inside of the hole that you dug for the footing. Use the 2x4s around the perimeter as a guide to hold the concrete in place while it dries.^{[3]
X
Research source}
- Make sure that the 2x4s are flush with the top of the hole that you dug. That way, the concrete won’t spill out of the top.
4
Pour the base concrete. Mix a batch of concrete in a wheelbarrow with a shovel. Fill the frame that you just dug up to the edge. Level the freshly poured concrete by running a 2x4 across the top, and fill any spots that are low with additional concrete.^{[4]
X
Research source}
- For a large retaining wall, consider renting or hiring a concrete mixing truck to come and pour the concrete for you.
5
Wait 3 days for the footing to dry. Before you can begin building, you'll need to give the concrete ample time to dry. Building on wet concrete can lead to sagging, and your concrete wall may not be as sturdy as it needs to be.^{[5]
X
Research source}

Part 2

Part 2 of 2:

Laying Concrete Blocks with Mortar

1
Section off the corners with wooden stakes. Before you begin laying the blocks, visualize all the corners of your frame. Place a wooden stake in each corner, and use a cord or string to tie off exactly where the corners’ edges will be. Attach a cord or string to the wooden stake used to mark the corners and lay out a perimeter.^{[6]
X
Research source}
2
Mix cement mortar with water. Take the bag of dried concrete, and look at the bag's specifications to find the ratio of mortar to water. Use a 5-gallon bucket or a wheelbarrow to mix the mortar with a shovel until it’s thick and paste-like.^{[7]
X
Research source}
- Type M mortar is the strongest mortar mix out there, so it’s ideal for this project.
- Use a drill and a mortar mix drill bit to make this process easier.
- Try not to mix more mortar than you can use. Mortar dries out quickly, and any extra mortar you have will need to be thrown away.
- Wear protective glasses, gloves, a ventilated mask, and long jeans.^{[8]
  X
  Expert Source
  
  Gerber Ortiz-Vega
  Masonry Specialist & Founder, GO Masonry LLC
  Expert Interview. 10 March 2020.}
3
Spread the mortar along 1 corner of the footing. Use your trowel to spread a few slabs of mortar around the corner's base of the footing. Spread the mortar 1 in (2.5 cm) deep and 8 in (20 cm) wide in the marked area. Continue to spread the mortar to account for the distance of about 3 to 4 blocks.^{[9]
X
Research source}
- You may notice that the mortar falls off your trowel quickly, which can be frustrating. To keep it contained, scoop mortar up with your trowel, then tap the flat side of the trowel onto a flat surface. The remaining mortar will be thin and stick to the trowel until you’re ready to apply it.
4
Center the corner block on the footing. Stand over the footing and gently set the concrete block down, making sure it’s level and flat. Center the corner block in the footing by measuring around the block and making sure it’s even.^{[10]
X
Research source}
- Use your string to make sure your corner block is level and in a straight line.
5
Continue to lay the concrete blocks in a line out from the corner. Start laying blocks from the corner or edge of the wall to work in one direction. Apply a 1 in (2.5 cm) thick layer of mortar to the sides of each block as you go.^{[11]
X
Research source} Keep laying blocks and applying mortar until you reach the next corner.
- Apply mortar at the end of the block before you place the block adjacent to it.
6
Check the alignment of the blocks with a level. Before stacking more concrete blocks on top of your initial foundation, check if everything is aligned.^{[12]
X
Expert Source

Gerber Ortiz-Vega
Masonry Specialist & Founder, GO Masonry LLC
Expert Interview. 10 March 2020.} Use your mason's level by laying it on the first set of blocks. Check both the outside and center section of the bricks.
- Tap the blocks for any alignment adjustments while the mortar is still wet.
- Do not try to move a block after the concrete has set, since that could make your wall unstable.
7
Apply mortar to the top of the blocks. Use your trowel to spread 1 in (2.5 cm) of mortar over the entire width of the block.^{[13]
X
Research source} Then, spread the mortar so it covers the length of about 3 blocks in the direction that you are laying the bricks.
- Keep the mortar on the sides of the blocks so that it doesn’t fall into the hollow center. It won’t hurt your retaining wall, but it will just waste your mortar.
8
Stack the blocks on top of each other. Lay the block down on top so the edge of the top block aligns with the halfway mark of the bottom block. You'll recognize the pattern as a standard among the construction sites. The top block will fit in between 2 bottom blocks.^{[14]
X
Research source}
- Use a level every 2 to 3 layers to ensure your wall is flat. If not, remove bricks from the uneven layer and try again.
9
Add reinforcement rods for high walls. If you’re building a house or a large shed, consider adding reinforcements. You can also use reinforcements if the ground pressure on the site is not stable. Place the 1/4" steel reinforcement rods into each opening of the concrete blocks.^{[15]
X
Research source}
10
Strike the mortar joints. The mortar joints are the spaces between the bricks that are filled with mortar. Once the mortar mix has set enough so you can leave a thumbprint in it, run a concave jointing tool along each joint to remove the excess mortar. Start with the horizontal joints, then move to the vertical joints.^{[16]
X
Research source}
- For best results, move across each joint 2 times, and keep your tool wet.
- There are several different joints to choose from, but the concave joint is the easiest to do for beginners.
11
Wait 24 hours for the mortar mix to cure. Mortar mix will start drying within 20 to 40 minutes, but it’s best to wait at least 24 hours before adding anything on top of your walls. After 1 day or so, the mortar mix will be mostly cured, and it will be strong enough to support other construction materials.^{[17]
X
Research source}
- Mortar mix can take up to 28 days to reach its full cured strength.

Expert Q&A
Did you know you can get expert answers for this article? Unlock expert answers by supporting wikiHow

Question

How do I clean my tools after mixing the mortar?

Gerber Ortiz-Vega
Masonry Specialist & Founder, GO Masonry LLC
Gerber Ortiz-Vega is a Masonry Specialist and the Founder of GO Masonry LLC, a masonry company based in Northern Virginia. Gerber specializes in providing brick and stone laying services, concrete installations, and masonry repairs. Gerber has over four years of experience running GO Masonry and over ten years of general masonry work experience. He earned a BA in Marketing from the University of Mary Washington in 2017.

Gerber Ortiz-Vega

Masonry Specialist & Founder, GO Masonry LLC

Expert Answer

Support wikiHow by unlocking this expert answer.

Scrub them with water and a wire brush until all of the mixture is off of them. Make sure you clean them immediately after you're finished using them so the mortar doesn't dry.
Question

I'm doing a straight cinder block wall (3 high) dividing property. Do I need reinforcement rods? Can I just lay cinder blocks in the ground first, then use mortar with 2 layers of remaining?

Community Answer

Only do that if you want the wall to sink in the ground. You need a footing to support the wall.
Question

How do I lay a 45 degree corner?

Community Answer

Cut the corners with a concrete cutting saw at a 22.5 degree angle, using a diamond blade. Don't forget to use a mask so that you don't choke from concrete dust inhalation.

Warnings

Always wear protective glasses, gloves, a ventilated mask, and long jeans when you're mixing mortar.^{[18]
X
Expert Source

Gerber Ortiz-Vega
Masonry Specialist & Founder, GO Masonry LLC
Expert Interview. 10 March 2020.}

⧼thumbs_response⧽
Helpful 0 Not Helpful 0