Updating your kitchen is one of the best ways to increase the value of your home. Even just changing your kitchen cabinets can completely revitalize the look and feel of your kitchen. They’re also not as difficult to install as you may think. If you have some carpentry experience and experience with power tools, you can get the job done relatively easily.

Part 1
Part 1 of 4:

Marking Layout Lines

  1. 1
    Use a 4-foot (1.2 m) level to check that your walls are plumb. Take a long level and place it up right against your walls. Look at the bubble in the tube to check if the wall is plumb, which means it’s perfectly vertical. Place your level onto different sections of the well to check that it’s plumb all around.[1] If any parts of your wall aren’t plumb, make a note of any dips or angles that you’ll need to shim or make alterations for to make sure the cabinets are level.[2]
    • For instance, if the bottom portion of your wall slopes outward a bit, you may need to add shims, which are small wedges used to make small adjustments, when you install your cabinets so they’re even.
  2. 2
    Mark a level reference line about 48 inches (120 cm) off the floor. Take a ruler or tape measure and measure the distance from the floor to the center of your wall. Mark an even line all across the wall with a pencil, marker, or chalk.[3]
    • This will serve as a simple reference point for you to take more measurements.
    • Make sure the line is even all around so your future measurements are accurate!
    • You could also use a laser level for a simple way to create an accurate reference line.
    Advertisement
  3. 3
    Measure down to the floor from the line to find your highest point. Use your ruler or tape measure and measure straight down from the reference line down to the floor. Take multiple measurements along the line and look for the highest point of your floor. Once you identify it, make a small marking on your wall so you can remember where it is.[4]
    • Finding your floor’s highest point is super important for installing your cabinet evenly.
  4. 4
    Mark a level line 34.5 inches (88 cm) above the highest point of the floor. Measure up from where you marked your floor’s highest point and use a pencil, marker, chalk, or laser level to mark a line across your wall. Make sure the line is even so your cabinets will be level when you install them.[5]
    • This layout line marks where the tops of your base cabinets will be once they’re installed.
  5. 5
    Measure and mark a line 17–18 inches (43–46 cm) above the layout line. Use your ruler or tape measure to measure up from the layout line you just marked. Mark the layout line for your upper cabinets with a pencil, marker, or chalk.[6]
    • This line also marks the bottom edge of your upper cabinets.
  6. 6
    Locate and mark the studs on both layout lines. Find your wall studs with a stud finder or by knocking to locate solid spots where studs are located. Use your pencil, marker, or chalk to mark all of the wall studs located in your layout lines.[7]
  7. 7
    Add markings for any appliances and fixtures you’ll install. If you’re planning to add appliances such as refrigerators or any fixtures, measure them first so you know how much space you need to leave open. Mark their measurements on your walls so you can install your cabinets around them.[8]
  8. Advertisement
Part 2
Part 2 of 4:

Hanging the Upper Cabinets

  1. 1
    Drill cleats into studs beneath the layout line of the upper cabinets. Cleats are essentially small shelves that you can use to support your cabinets while you’re installing them. Place a straight cleat just beneath the layout line for your upper cabinets and drill 2-inch (5 cm) drywall screws through them into every other stud so they’re firmly attached and can hold the weight of your cabinets. Add a cleat for every cabinet you plan to install so their weight is fully supported when you hang them.[9]
    • Attach cleats along the length of your upper cabinet layout line.
  2. 2
    Align and clamp the frames of your upper cabinets together. Place your upper cabinets together on your floor. Line up the edges of the frames and clamp them together firmly and securely.[10]
    • Go with either ratchet or screw clamps. Squeeze clamps won’t be strong enough to hold the cabinets in alignment.[11]
  3. 3
    Mark stud locations and drill holes through the back. Line up your cabinets against the wall and mark the locations of wall studs on the back. Take a drill and create pilot holes into the back of the cabinet where the studs are located. Drill pilot holes at both the top and bottom of your cabinet so they’re ready to go when you hang them.[12]
    • Make sure the pilot holes are large enough to fit your 2-inch (5 cm) screws.
  4. 4
    Drill the upper cabinets together with 2-inch (5 cm) screws. Fit the screws onto your drill and drive them through both of the frames you have clamped together so they’re connected. Drill screws into the tops and bottoms of both frames so they’re securely fastened.[13]
  5. 5
    Lift the cabinets up onto the cleats. Have another person help you or use a cabinet jack to carefully lift the cabinets from the floor. Gently place them onto the cleats and push the cabinets flush against your wall.[14]
    • It can be tough to lift the cabinets on your own, and you could damage them if you drop them. Try having a friend lend a hand so you can do it safely.
  6. 6
    Drive screws through the back of the cabinets. Use 2-inch (5 cm) screws and drive them through the upper holes you created in the back of the cabinet and into the wall stud behind them. Then, drive screws through the bottom holes to firmly attach the cabinets to your wall.[15]
  7. 7
    Remove the cleats and shim the cabinets if you need to. Unscrew and carefully remove the cleats from your wall since your cabinets are now attached to the studs. Check the cabinets to make sure they’re even along your walls. If there are any uneven sections, add shims to the space between the wall and your cabinets until they’re flush and even.[16]
  8. Advertisement
Part 3
Part 3 of 4:

Connecting the Base Cabinets

  1. 1
    Position the first cabinet in the corner and make sure it’s level. Choose a corner to start installing your base cabinets. Move your first corner cabinet into place and use your level to see how evenly it sits.[17]
    • Make a note if the cabinet is uneven. You may need to add shims later if it is.
  2. 2
    Mark any plumbing lines and drill holes to fit them in the back of the cabinet. If you have any plumbing lines that need to run through your cabinet, push your cabinet against the line and mark the location on the back. Then, use a drill to create holes large enough to fit the lines.[18]
  3. 3
    Shim the top and face of the cabinet so it’s level. Push your cabinet flush against the wall and place your level across the top of it. Add shims beneath the cabinet or in the space between the wall and the back of it as necessary until the top and face are even and stable.[19]
  4. 4
    Drill wood screws through the back of the cabinet into the wall studs. Drive the screws right through the back of the cabinets and into the wall studs behind them. Drill a screw into each of the studs so the cabinet is firmly and securely connected to your wall.[20]
  5. 5
    Align each additional cabinet evenly and install them. Once the corner cabinet is installed, place another one next to it. Check to make sure it’s level and add shims as necessary until it is. Drive screws through the back of the cabinet into the wall studs behind it. Then, move on to the next one until all of the base cabinets are installed.[21]
  6. Advertisement
Part 4
Part 4 of 4:

Attaching Doors, Drawers, and Trim

  1. 1
    Screw the cabinet doors into place. For traditional hinges, drive small screws through the hinges into doors. If your cabinet doors snap into place, install them into the proper slots. Open and close the doors a few times to make sure they’re firmly and securely attached.[22]
    • Your cabinet doors likely came with special screws for you to use, but if you don’t have them, try looking up the cabinets online to see what screws you need to use.
    • If any of the doors are hanging unevenly, remove and adjust the hinges, and reattach the doors to straighten them out.
  2. 2
    Fasten the toekick trim with 1-inch (2.5 cm) brads. Toekick trim covers the small gap between the base of your cabinets and the floor. Fit the toekick into place and drive small brads, also known as brass fasteners, into it to secure it.[23]
  3. 3
    Set the drawers in their tracks and push them into place. Align the tracks on the bottom of a drawer with the tracks in the drawer-slot of your cabinet. Slide your drawer onto the track and push it all the way into your cabinet. Add any additional drawers following the same method.[24]
  4. Advertisement

Community Q&A

  • Question
    How many inches should there be from the bottom cabinets to the upper cabinet?
    Community Answer
    Community Answer
    Typically, you should leave 18" between the counter top and the base of the upper cabinets. Some people change this by an inch or two depending on individual heights and other factors.
  • Question
    What should I do with the shims that I put under the lower cabinets?
    Community Answer
    Community Answer
    You should leave all shims in place. The ones in the back get cut off, screwed through, and covered by the counter top. Those underneath should be cut off at the edge of the cabinet so they don't interfere with adjacent cabinets.
  • Question
    How do I install base cabinets when they are not against a wall? They are open in the middle of the kitchen.
    Community Answer
    Community Answer
    You screw 2x4 boards to the floor on what would be the inside of the cabinets, and then screw the cabinets to these boards.
Advertisement

Warnings

  • Avoid trying to lift the upper cabinets yourself. You could injure yourself and potentially damage the cabinets if you drop them.
    ⧼thumbs_response⧽
  • If you have gas or electric lines that need to be run through your cabinets, contact a professional such as a licensed contractor or electrician so you can make sure the job is done safely and up to code.
    ⧼thumbs_response⧽
Advertisement

About This Article

Kevin Schlosser
Co-authored by:
Home Improvement Specialist
This article was co-authored by Kevin Schlosser. Kevin Schlosser is a Home Improvement Specialist and the Owner of Home Tech Handyman Ltd. With over 20 years of experience, Kevin specializes in age-in-place installations, flooring, roofing, and general remodeling handyman services. Kevin holds a blend of construction and in-home technology-related certifications including NAHB Certified Age-in-Place Specialist, CEDIA membership and certifications, and a Certification from the Association of Certified Handyman Professionals. Also, he is in training to receive certifications in Construction, Project Management, and other CEDIA qualified system integrator certifications. He is fully-insured in the state of Colorado. This article has been viewed 680,240 times.
5 votes - 80%
Co-authors: 41
Updated: March 14, 2023
Views: 680,240
Advertisement