Wood letters are a fun, creative way to spice up a room, allowing you to add names, words, or even full sentences to your wall. There are a number of different ways to hang the letters up, meaning you can choose the method most appropriate for your project, such as nails or ribbon for drywall or adhesive for brick.

Method 1
Method 1 of 3:

Using Adhesives

  1. 1
    Mark the spot where you want to hang the letter. Hold your letter up against the wall and adjust it until you think it looks good. Then, using a pencil or the corner of a sticky note, mark the wall at the top center edge of the letter. If you’re putting up multiple letters, make marks for each before hanging anything up to avoid issues with spacing.[1]
  2. 2
    Choose an adhesive based on the size and weight of the letters. For heavier letters, grab double sided mounting tape, large Velcro strips, or another thick, durable adhesive. For medium-weight letters, try Command strips or a similar resealable fastener. For small letters, you may be able to use sticky tack or a generic brand of tape.[4]
    Advertisement
  3. 3
    Prepare the adhesives. If you’re using tape, rip off multiple pieces and roll them into small, hollow tubes with the sticky sides facing out. If you’re using fasteners or similar items, remove the small strips of paper covering the sticky sides of the adhesives. For tack, pull off multiple pieces and roll them into small balls.[6]
  4. 4
    Press the adhesives to the back of your letter. Place the adhesives at multiple points on the back of the letter, spacing them out evenly so that each area has some support. If you’re using tape, tack, or other small adhesives, focus on joints and corners since they will help keep the letter flat against the wall. If you’re using large fasteners or Velcro strips, place them on long stretches of wood so they can support the bulkiest part of the letter.[7]
    • For Velcro and other adhesives that come in 2 parts, press both parts together before sticking your letter to the wall.
  5. 5
    Stick your letter to the wall. Hold your letter up so that the top center edge touches the mark you made earlier. Then, press it to the wall. Make sure to push down on every area containing an adhesive to ensure the letter is fully attached. If you’re using adhesives like Command strips, hold them down for the amount of time listed on the packaging.
  6. Advertisement
Method 2
Method 2 of 3:

Mounting a Wooden Letter with Nails

  1. 1
    Mark the spot on your wall where you want to hang the letter. Press your letter to the wall and move it around until you’re happy with the position. Then, mark the top center edge of the letter with a pencil or the corner of a sticky note. To avoid spatial conflicts, make marks for every letter you intend to put up before hanging anything.[8]
  2. 2
    Drill small holes in the back of your letter if necessary. Grab a power drill and, with the speed on low, create small holes in the back of your letter. Use a drill head that can create holes larger than the nail you plan on hanging your letter from. The thicker the letter, the deeper the holes should be. If your letter came with pre-drilled holes, skip this step.[10]
    • If your letter is symmetrical, drill 1 or more holes near the top center of the object.
    • If your letter is not symmetrical, in addition to a hole near the top center of the object, drill holes in any areas where the weight is strangely distributed, such as the bottom hook on a ‘J.’
  3. 3
    Make marks on your wall where the nails will go. Hold your letter up to the wall so that the top center edge touches the mark you made earlier. Then, create small pencil marks on the wall that correspond with the holes in the back of your letter. To make sure the marks are accurate, use a tape measure to find the distance between them and compare them to the distance between the holes in your letter.
    • Also, use a laser level or ask someone to hold a bubble level where you want the base of the letters to go. This will help you make sure the letters are straight.[11]
  4. 4
    Hammer nails into the marked areas. Grab a nail with a head that is slightly smaller than the holes in the back of your letter. Hold it up against one of your marks and, with a hammer, gently pound it into the wall. Leave enough of the nail exposed that you can easily hang your letter on it. Repeat this for each mark.[12]
    • For heavier letters, try using wall anchors instead of nails.
  5. 5
    Hang your letter on the nails. Place the holes in the back of your letter over the corresponding nails. Then, remove your hands from the letter to make sure the nails can fully support it. If the nails are positioned incorrectly, move them to a new spot. If they cannot hold the letter, try replacing them with a sturdier object like a wall anchor.
  6. Advertisement
Method 3
Method 3 of 3:

Hanging a Wooden Letter Using Ribbon

  1. 1
    Make marks on your wall where you want your letter and ribbon to sit. Press your letter onto the wall at the spot you want to hang it from. Adjust the letter until you’re happy with the placement, then mark the top center edge of it with a sticky note or pencil. Using the same method, mark the position directly above your letter where you want the top of your ribbon to sit.[13]
  2. 2
    Find the distance between the 2 marks. Using a tape measure, find the distance between the ribbon mark and the letter mark. The tape measure should go from just below the letter mark to just above the ribbon mark.[14]
  3. 3
    Cut out a piece of ribbon just over twice as long as your measurement. With your tape measure as a guide, stretch out a piece of ribbon that is twice as long as the distance between the 2 marks. Before cutting, pull out an extra 1 to 2 inches (2.5 to 5.1 cm) to account for the fact that you’ll be attaching the ribbon to the back of the letter, not the top edge. Then, cut the ribbon off the spool using scissors.[15]
  4. 4
    Fix the ribbon to the back of your letter using hot glue. With a glue gun, place 2 patches of hot glue on the back of your letter. Make sure the patches are spaced evenly apart. Then, press the ends of your ribbon onto the glue, creating a loop. Let the glue dry for 1 to 2 minutes.[16]
  5. 5
    Hammer a nail into the ribbon mark. Grab a nail strong enough to hold your letter; for most letters, a 4D or 6D nail will be more than enough. Then, place it directly over the ribbon mark and gently hammer it into the wall. Leave a portion of the nail exposed so you can hang your ribbon from it.[17]
  6. 6
    Hang your ribbon from the nail. Place the center of your ribbon loop over the nail. Let it sit for a few minutes to make sure both the hot glue and nail are sturdy enough to hold your letter. If the letter doesn’t hang where you want it to, try adjusting the ribbon or moving the nail. If the nail can’t support your letter, try replacing it with a strong screw or wall anchor.
  7. Advertisement

Expert Q&A
Did you know you can get expert answers for this article? Unlock expert answers by supporting wikiHow

  • Question
    How do you know how to space out the letters?
    David Julien
    David Julien
    DIY Specialist
    David Julien is a DIY Specialist and the Principal Owner at Nice DIY based in Quebec, Canada. David specializes in creating plans to make unique, affordable, and modern home furnishings. He holds a BA in Graphic Design from the University of Quebec Outaouais. Nice DIY uses sustainable and high-quality materials to create products that are simple to make for everyone.
    David Julien
    DIY Specialist
    Expert Answer

    Support wikiHow by unlocking this expert answer.

    Start by placing the letters on the floor to visualize the space you want between them.
  • Question
    How do I make sure the letters are level?
    David Julien
    David Julien
    DIY Specialist
    David Julien is a DIY Specialist and the Principal Owner at Nice DIY based in Quebec, Canada. David specializes in creating plans to make unique, affordable, and modern home furnishings. He holds a BA in Graphic Design from the University of Quebec Outaouais. Nice DIY uses sustainable and high-quality materials to create products that are simple to make for everyone.
    David Julien
    DIY Specialist
    Expert Answer

    Support wikiHow by unlocking this expert answer.

    Use a laser level or ask someone to hold a bubble level where you want the base of your letters on the wall.
  • Question
    What kind of adhesive should I use to hang letters?
    David Julien
    David Julien
    DIY Specialist
    David Julien is a DIY Specialist and the Principal Owner at Nice DIY based in Quebec, Canada. David specializes in creating plans to make unique, affordable, and modern home furnishings. He holds a BA in Graphic Design from the University of Quebec Outaouais. Nice DIY uses sustainable and high-quality materials to create products that are simple to make for everyone.
    David Julien
    DIY Specialist
    Expert Answer

    Support wikiHow by unlocking this expert answer.

    Glue the letters with double-sided tape designed for this purpose and which will not damage the paint.
Advertisement

Things You’ll Need

Mounting a Wooden Letter with Nails

  • Wooden letter
  • Pencil or sticky notes
  • Tape measure
  • Hammer
  • Nails or wall anchors
  • Power drill (if necessary)

Using Adhesives

  • Wooden letter
  • Pencil or sticky notes
  • Adhesives (tape, Velcro strips, resealable fasteners, or sticky tack)

Hanging a Wooden Letter Using Ribbon

  • Wooden letter
  • Ribbon
  • Pencil or sticky notes
  • Tape measure
  • Scissors
  • Hot glue gun
  • Hammer
  • Nail, wall anchor, or strong screw

Warnings

  • Be careful when working with tools like hammers and power drills. For safety, wear heavy duty working gloves and goggles during use.
    ⧼thumbs_response⧽
Advertisement

About This Article

David Julien
Co-authored by:
DIY Specialist
This article was co-authored by David Julien. David Julien is a DIY Specialist and the Principal Owner at Nice DIY based in Quebec, Canada. David specializes in creating plans to make unique, affordable, and modern home furnishings. He holds a BA in Graphic Design from the University of Quebec Outaouais. Nice DIY uses sustainable and high-quality materials to create products that are simple to make for everyone. This article has been viewed 63,705 times.
2 votes - 50%
Co-authors: 6
Updated: June 17, 2022
Views: 63,705
Categories: Wooden Craft Projects
Article SummaryX

To mount a wooden letter, start by placing the letter on your wall and, when it’s positioned how you want it, mark the top edge with a pencil or sticky note. If your letter did not come with premade holes, drill some into the back of the wood. Then, press your letter against the top edge mark and create additional marks on the wall corresponding to each of the letter’s holes. Hammer nails into the marked areas to create hooks, then hang your letter from them. To learn how to hang wooden letters using ribbon or adhesives, read on!

Did this summary help you?
Advertisement