wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 23 people, some anonymous, worked to edit and improve it over time.
wikiHow marks an article as reader-approved once it receives enough positive feedback. In this case, 91% of readers who voted found the article helpful, earning it our reader-approved status.
This article has been viewed 473,728 times.
Learn more...
Storing canned food in your kitchen cabinets is an inefficient use of space and you will often find old cans in the back. This easy-to-build shelf system will solve the problem by rotating the cans. The cost is a small fraction of the price of retail canned food systems. There are many variations, so modify the plans to suit your needs and abilities.
Steps
-
1Decide the size and number of shelves you need. This article will cover a 5-shelf system that is 32 inches (81.3 cm) wide, 24 inches (61.0 cm) deep and 64 inches (162.6 cm) tall.[1]
-
2Cut the plywood on a table saw or with a circular saw.
- Cut one full sheet in half length-wise. From each half, cut a shelf at 32 inches (81.3 cm) (should leave 64 inches for the sides).
- Cut the other full sheet in half length-wise also. Cut each half in thirds at 32 inches (81.3 cm) each.
- Cut the half-sheet of plywood at 32 inches (81.3 cm). Cut the 32x48 piece in half (24x32). Set the remaining 16x48 piece aside for later. You should have 2-24x64 and 10-24x32.
Advertisement -
3Using a router and straight edge, rout slots into the sides 3⁄4 inch (1.9 cm) wide and 1⁄2 inch (1.3 cm) deep. (An alternative is to attach rails that the shelves will rest on. The slot method is stronger and will not interfere with the rolling cans.)[2]
- The shelves need to have a 1:12 slope (1 inch drop for each 12 inches run).
- For standard cans, the distance from the top of the input shelf to the top of the corresponding output shelf is 8 inches (20.3 cm).
- For standard cans, the distance from the top of the input shelf, to the top of the next output shelf is 4 inches (10.2 cm).
- For standard cans, the input shelf is 3.5 inches (8.9 cm) shorter than the output shelf.
- For larger cans, add 1 inch (2.5 cm) to these dimensions.
- Draw outlines for all slots.
-
4Trim the shelves. The finished outside width of the shelf system will be 32 inches (81.3 cm). The shelves will fit in a slot 1⁄4 inch (0.6 cm) deep. Therefore, the width of the shelves is actually 31 inches (78.7 cm). Each input shelf also needs to be trimmed on the back to allow a space for the can to drop. For standard cans, this gap needs to be 3.5 inches (8.9 cm).
-
5Lay one side flat on the ground with the slots facing up. Insert the shelves into the slots and place the other side on top.
-
6Drive 2 inch (5.1 cm) screws through the side and into the edge of the shelf. Put two screws in each shelf.[3]
-
7Turn the unit over and drive screws in this side also.[4]
-
8Turn the unit over so the back is facing up. Attach the pieces that were cut from the input shelves to prevent the cans from falling off the back.[5]
-
9From the 16x48 scrap plywood, cut 5 pieces 2x32 inch. Turn the unit over so the front is facing up. Attach the 2x32 inch pieces to block the cans from falling out the front.[6]
-
10With the remaining plywood and/or additional scrap you have laying around, build a base that the casters will attach to. Stand the unit upright and attach it to the base.
-
11Decide the configuration of cans that you need. Each row will need to be about 1⁄2 inch (1.3 cm) wider than the can. On the table saw, rip 1⁄4 inch (0.6 cm)-wide strips from plywood, MDF, or dimensional lumber. MDF and lumber work best. Attach them to the shelves with wood glue.
-
12One problem you may have is the cans getting misaligned when they drop down.
- A solution for this is to add a divider connecting the row dividing strips, filling the gap. Cut cardboard in a trapezoidal shape to fit over the two row dividers. Cut out the center material of the cardboard and glue the flaps to the row dividers.
- A solution for this is to add a divider connecting the row dividing strips, filling the gap. Cut cardboard in a trapezoidal shape to fit over the two row dividers. Cut out the center material of the cardboard and glue the flaps to the row dividers.
-
13Another problem occurs when the gap is too large for the cans. The can can get blocked, preventing other cans from dropping down.
- A solution for this problem is to glue wedges at the back of the lower shelf. This will cause the can to roll forward before the next one locks it in. The wedges can be cut from the same material used for the row dividers. They should be large enough to move the can forward.
- A solution for this problem is to glue wedges at the back of the lower shelf. This will cause the can to roll forward before the next one locks it in. The wedges can be cut from the same material used for the row dividers. They should be large enough to move the can forward.
-
14Start using the rotating canned food shelf. Add labels to the front of each row to identify the contents and load cans in the top portion of each shelf.
Community Q&A
-
QuestionHow can I print sample pictures, not just instructions? Would like very much to have full instructions and pictures?Community AnswerUse Print Friendly, from there you can delete the ads and adjust the picture size, then either print or save it to PDF.
Warnings
- Always wear safety glasses when operating or using any type of power tool.⧼thumbs_response⧽
- Power tools can be dangerous; stay attentive and use with care.⧼thumbs_response⧽
Things You'll Need
- 4 casters (3 inch)
- 2.5 sheets 3/4" plywood
- MDF or lumber
- Wood glue
- 2 inch (5.1 cm) screws
- Table saw
- Circular saw
- Router with 3/4in bit
- Drill
References
- ↑ https://www.buildmyowncabin.com/canrotator/food-can-rotation-system.html
- ↑ https://www.buildmyowncabin.com/canrotator/food-can-rotation-system.html
- ↑ https://www.youtube.com/watch?v=qLoBaXVDBzg
- ↑ https://www.youtube.com/watch?v=qLoBaXVDBzg
- ↑ https://www.shanty-2-chic.com/2012/10/pantry-ideas-diy-canned-food-storage.html
- ↑ https://www.shanty-2-chic.com/2012/10/pantry-ideas-diy-canned-food-storage.html