How to Replace a Thermostat in a Car

A vehicle’s thermostat controls the amount of coolant running through the engine so it doesn’t overheat. But if your temperature gauge consistently stays past the ¾-mark or in the red zone when you run your vehicle, it could be a symptom of a bad thermostat that needs to be replaced. Luckily, it only takes a few minutes and a couple of tools to change your thermostat yourself. Our guide will show you how to remove the bad thermostat and replace it with a new one!

Part 1
Part 1 of 3:

Removing the Old Thermostat

  1. Image titled Replace a Thermostat in a Car Step 1
    1
    Wait for the engine to cool down if you drove recently. As you drive your vehicle, the coolant running through the engine heats up and could cause severe burns. Before you make your repairs, give your vehicle 30–60 minutes so it can cool off. To check the temperature, open the hood and lightly touch your engine to see if it feels hot. If it’s cool to the touch, then you can work safely.[1]
    • Never work on your vehicle while it’s running since you could get injured.
    • Try leaving the hood open to help your engine cool off faster.
  2. Image titled Replace a Thermostat in a Car Step 2
    2
    Take the cap off of your radiator. Locate your radiator, which is a long black box under your hood and in the front of your engine bay directly behind the grille. Look for a circular cap on top of the radiator and turn it counterclockwise to loosen it. Set the cap aside while you’re working so you don’t misplace it.[2]
    • Never open the radiator cap if your engine is still hot. The radiator may have built-up pressure, which could spray hot coolant when you open the cap.
    • If you notice coolant leaking out from the radiator cap before you unscrew it, buy a replacement.

    Variation: Your vehicle may have a clear plastic reservoir near the back corner of the engine bay that stores additional coolant. You can unscrew the reservoir cap instead of the radiator cap.

    Advertisement
  3. Image titled Replace a Thermostat in a Car Step 3
    3
    Put a drip pan underneath your radiator’s drain plug. Look underneath your vehicle at the bottom of the radiator and look for a small plastic wingnut or plug. Slide a drip pan directly under the plug so your coolant doesn’t spill everywhere or make a mess while you’re working.[3]
    • You can buy a drip pan from an automotive supply store. If you don’t have a drip pan, you can also use a bucket.
    • You may need to jack your vehicle onto stands if you can’t get under your vehicle to find the drain plug.
  4. Image titled Replace a Thermostat in a Car Step 4
    4
    Drain half of the coolant out from your radiator’s drain valve. Turn the drain plug on your radiator counterclockwise until you see a steady stream of coolant pour into the drip pan. Check the levels of the coolant by looking into the radiator. You only need to remove enough coolant to expose the thermostat, so once half of the coolant flows out from the plug, turn it clockwise to tighten it again.[4]
    • You do not need to drain all of the coolant from your vehicle.
    • Save the coolant you drained since you can keep using it.
    • If your coolant is filled with dirt or floating debris, you may need to flush your radiator to clean it.
  5. Image titled Replace a Thermostat in a Car Step 5
    5
    Unbolt the thermostat housing from the engine block with a ratchet. Follow the hose from the top of your vehicle’s radiator to the side of your engine. Where the hose connects to the engine will be the housing for the thermostat. Find the 2 bolts on each side of the housing’s flange and turn them counterclockwise with a ratchet. Once you loosen the bolts, you can easily lift the housing up to detach it from the engine.[5]
    • You do not need to remove the radiator hose, but you can unclamp it if you have trouble reaching the housing’s bolts.
    • If the housing has dents or pitting, you should also replace it.
  6. Image titled Replace a Thermostat in a Car Step 6
    6
    Pull the old thermostat out with a pair of pliers. Check the port on your engine where you removed the housing to locate the thermostat, which looks like a cylinder with a metal ring around the outside and a pointed valve on top. If you don’t see the thermostat in the engine port, it may be stuck in the housing end with the hose. Grip the top of the thermostat with the pliers and pull it straight out. If the thermostat feels stuck, try twisting it as you pull it out.[6]
    • Save the old thermostat until you get a new one or take pictures of it to ensure that you buy one that’s exactly the same.
    7. Advertisement
Part 2
Part 2 of 3:

Installing the New Thermostat

  1. Image titled Replace a Thermostat in a Car Step 7
    1
    Get a replacement thermostat and gasket with the same heat rating. Look around the thermostat’s ring for a temperature listing, which is when the thermostat opens and allows coolant to pass through the engine. Look at an automotive store for a thermostat that lists the same opening temperature, or else your vehicle may not operate properly. Then look for a thermostat gasket that matches the shape of the housing’s flange so the coolant doesn’t leak while your vehicle runs.[7]
    • New thermostats and gaskets usually cost over $50 USD total, but it may be more expensive depending on the make and model of your vehicle.[8]
    • The type of gasket you buy depends on the make and model of your vehicle.
  2. Image titled Replace a Thermostat in a Car Step 8
    2
    Remove any residue from the housing and engine flanges with a scraper. Hold your scraper against the housing flange at a 45-degree angle. Use light pressure to scrape off the residue that was leftover from the old gasket. Keep cleaning the flange until it’s smooth. Then scrape the flange on the engine.[9]
    • If you don’t clean off the residue, then the housing won’t sit properly and could cause coolant to leak.
    • Avoid being too forceful with your scraper since the thermostat housing is usually made from aluminum and can easily get damaged or dented.
  3. Image titled Replace a Thermostat in a Car Step 9
    3
    Put the thermostat in the engine flange so the valve points up. Inspect your new thermostat to find the pointed valve on top and the spring on the bottom. Slide the thermostat into the port on your engine and push it in tightly. Make sure the thermostat’s ring fits perfectly in the port, or else coolant will be able to leak through.[10]
    • If you install the thermostat with the spring side face-up, it won’t open properly and could cause your engine to overheat.
  4. Image titled Replace a Thermostat in a Car Step 10
    4
    Line the new thermostat gasket up on the flange. Your gasket will look like a flat piece of plastic or rubber that’s the same shape as the flanges. Put the gasket on top of the engine’s flange and line up the holes. Make sure you don’t block any of the holes or ports, or else the thermostat won’t work properly.[11]

    Variation: Depending on your vehicle’s make and model, you may need to install a circular gasket directly on the thermostat instead of setting one on the flange. Fit the thermostat’s ring into the groove running through the middle of the gasket before installing the thermostat.

  5. Image titled Replace a Thermostat in a Car Step 11
    5
    Bolt the housing back onto the engine. Set the housing on top of the gasket so the bolt holes line up. Turn the bolts clockwise by hand until they’re tight. Then use your ratchet to tighten the bolts until you feel resistance. Look up the torque specifications for your make and model of vehicle and only tighten the bolts by that amount.[12]
    • Avoid overtightening the bolts since you could easily damage the aluminum housing.
    6. Advertisement
Part 3
Part 3 of 3:

Refilling the Coolant

  1. Image titled Replace a Thermostat in a Car Step 12
    1
    Pour coolant into the reservoir up to the fill line. Locate the plastic coolant reservoir near the side or back corner of the engine bay. Open the cap and pour in the coolant you originally drained into the drip pan. If the coolant was dirty, then look up the coolant specifications for your vehicle and get a new bottle in the right color.[13] Keep pouring the coolant in until it reaches the fill line on the side of the reservoir.[14]
    • If your vehicle doesn’t have a reservoir, pour the coolant directly into your radiator.

    Warning: Vehicle coolant is toxic and can give off harmful vapors, so be sure to work in a well-ventilated area.[15]

  2. Image titled Replace a Thermostat in a Car Step 13
    2
    Screw on the radiator cap to seal it. Press the radiator cap back onto the opening on top of your radiator. Turn the cap clockwise to tighten it and seal the radiator so your coolant doesn’t splash or leak.[16]
    • If you don’t put the cap back on, then the thermostat and radiator won’t function properly and your engine may overheat.
  3. Image titled Replace a Thermostat in a Car Step 14
    3
    Start your vehicle’s engine to run coolant through the system. Turn the key in the ignition to run your vehicle’s engine. Leave the engine to idle for 5–10 minutes so the engine can warm up and activate your thermostat. As the engine runs, look at the thermostat housing to see if there are any leaks. After that, turn off your vehicle.[17]
    • Check the temperature gauge on your dashboard to make sure it stays below the ¾-mark. If the gauge still goes into the red zone, then there may be a leak or you've installed the thermostat improperly.
  4. Image titled Replace a Thermostat in a Car Step 15
    4
    Top off your coolant once your engine cools down again. Since the coolant will run into your engine and radiator, the levels may go down. Wait until your engine completely cools again so you don’t get burnt. Open the cap on the reservoir and check the coolant levels to see if you need to add more. Pour the coolant in until it reaches the fill line to ensure your engine doesn’t overheat.[18]
    • Avoid overfilling the coolant reservoir since it could cause damage if pressure builds up.
    5. Advertisement

Warnings

  • Always wait for your engine to cool down before you start working, or else you could get severe burns from the parts or the coolant.[19]
    ⧼thumbs_response⧽
  • Never drive your vehicle without the thermostat since your engine could easily overheat.[20]
    ⧼thumbs_response⧽
  • Vehicle coolant is toxic if ingested and can release harmful vapors.[21]
    ⧼thumbs_response⧽
Advertisement

Things You’ll Need

  • Drip pan
  • Ratchet
  • Pliers
  • Vehicle thermostat
  • Thermostat gasket
  • Metal scraper
  • Coolant

You Might Also Like

Reset Traction Control LightHow to Reset a Traction Control Light (TCS)
Fix a Locked Steering Wheel
How to
Fix a Locked Steering Wheel
Determine Gear Ratio
How to
Determine Gear Ratio
Reset Gas Gauge NeedleHow to Reset a Gas Gauge Needle
Change an Oxygen Sensor
How to
Change an Oxygen Sensor
Open the Hood of a VehicleHow to Unlock the Hood of Your Car
Open a Hood with a Broken Latch
How to
Open a Hood with a Broken Latch
Fix a Cigarette Lighter in a Car
How to
Fix a Cigarette Lighter in a Car
Remove Rust from Chrome
How to
Remove Rust from Chrome
Push Start a Car
How to
Push Start a Car
Reset Reduced Engine Power LightReduced Engine Power: What It Is and What to Do When You See the Warning Light
How to
Jack Up a Car
Use a Slim Jim
How to
Use a Slim Jim
Repair Leather Car Seats
How to
Repair Leather Car Seats
Advertisement

References

  1. ↑ https://www.automd.com/119/how-to-replace-a-thermostat/
  2. ↑ https://youtu.be/AOSRVxA_RRQ?t=195
  3. ↑ https://youtu.be/AOSRVxA_RRQ?t=207
  4. ↑ https://www.aa1car.com/library/thermostat_diagnose_replace.htm
  5. ↑ https://youtu.be/RIC6Z4D6Q3E?t=56
  6. ↑ https://youtu.be/RIC6Z4D6Q3E?t=65
  7. ↑ https://www.aa1car.com/library/thermostat_diagnose_replace.htm
  8. ↑ https://www.yourmechanic.com/services/thermostat-replacement
  9. ↑ https://youtu.be/BpYrLDjdcCA?t=29
  1. ↑ https://youtu.be/BpYrLDjdcCA?t=48
  2. ↑ https://www.readersdigest.ca/cars/maintenance/replace-thermostat-instructions/
  3. ↑ https://www.readersdigest.ca/cars/maintenance/replace-thermostat-instructions/
  4. ↑ https://www.machinerylubrication.com/Read/703/true-colors
  5. ↑ https://www.aa1car.com/library/thermostat_diagnose_replace.htm
  6. ↑ https://www.delaval.com/contentassets/ada4d8a60dda42c48e865dac1a816a7b/op1005---antifreeze-coolant---uk---09012017.pdf
  7. ↑ https://youtu.be/AOSRVxA_RRQ?t=360
  8. ↑ https://youtu.be/BpYrLDjdcCA?t=73
  9. ↑ https://www.aa1car.com/library/thermostat_diagnose_replace.htm
  10. ↑ https://www.aa1car.com/library/thermostat_diagnose_replace.htm
  11. ↑ https://www.aa1car.com/library/thermostat_diagnose_replace.htm
  12. ↑ https://images.homedepot-static.com/catalog/pdfImages/a1/a1e4bb1a-8d1c-49aa-ba8e-5b5c826e2082.pdf

About This Article

Hunter Rising
Co-authored by:
Hunter Rising
wikiHow Staff Writer
This article was co-authored by wikiHow staff writer, Hunter Rising. Hunter Rising is a wikiHow Staff Writer based in Los Angeles. He has more than three years of experience writing for and working with wikiHow. Hunter holds a BFA in Entertainment Design from the University of Wisconsin - Stout and a Minor in English Writing. This article has been viewed 20,784 times.
7 votes - 89%
Co-authors: 4
Updated: August 16, 2022
Views: 20,784
Categories: Car Maintenance and Repair
Advertisement