Vinyl car wraps can help promote a business by displaying logos and branding on your vehicle, but they wear out over time and may need to be replaced. If you have an old vinyl wrap that’s cracked or damaged, you can easily remove it yourself with only a few simple tools. There may be adhesive residue after you get the wrap off your vehicle, but it’s easy to clean off. When you’re finished, your vehicle will look new and ready for another wrap!

Part 1
Part 1 of 2:

Peeling off the Wrap

  1. 1
    Work in a shaded area out of direct sunlight. Working in the sun could make the adhesive bond to your vehicle’s body and makes it more difficult to remove. Work inside a garage if you can, or wait until there’s an overcast day to remove your wrap.[1]
    • Avoid removing the wrap in cold temperatures since the vinyl will rip in smaller pieces and leave residue.
  2. 2
    Lift the edges of the wrap with a plastic scraper. Find the edges of your wrap along the seams in your vehicle body, such as around the doors, hood, and trunk. Try to peel the edge slightly with your fingernail to get started. If you can’t lift the edge with your fingernails, slide a plastic scraper along the edge to start peeling it back.[2]
    • You can buy plastic scrapers at vehicle detailing shops or from a hardware store.
    • Don’t use any metal razor blades to peel the edges or else you could damage the vehicle body underneath.
    Advertisement
  3. 3
    Heat the wrap near the edges with a heat gun. Hold the heat gun 6 in (15 cm) away from your vehicle as you use it. Move the heat gun back and forth to distribute the heat evenly, so the adhesive sticks to the wrap instead of your vehicle. As you heat it, tug at the edge of the wrap to see if it removes easily.[3]
    • You can buy a heat gun from any hardware store or online.
    • Don’t heat any areas where the vinyl is covering chrome.[4]
    • Only heat the wrap enough so you can still comfortably hold it without wearing gloves.
  4. 4
    Pull the wrap off at a 15- to 20-degree angle from the vehicle. Slide both of your thumbs underneath the edge of your wrap and spread your fingers out on top of it. Lift the wrap so it’s at a 15-degree angle to the vehicle’s body and slowly pull up the wrap. Do your best to keep your wrap in a single piece as you remove it so it’s easier to take off.[5]
    • Avoid peeling the wrap off at a 90-degree angle since it will cause the adhesive to stick on your vehicle.
  5. 5
    Reheat the wrap if it gets difficult to remove. When the wrap cools down, the adhesive will stick to your vehicle’s body again and make it more difficult to peel off. Use your heat gun near the edge you’re peeling to reheat the adhesive. Heat the wrap evenly so all of the adhesive lifts as you pull off the wrap.[6]

    Tip: You can also pour water heated to 100 °F (38 °C) on the vinyl wrap just below the edge to cover an area more evenly.[7]

  6. Advertisement
Part 2
Part 2 of 2:

Removing Leftover Adhesive

  1. 1
    Spray a chemical adhesive remover on any residue and let it soak for 1 minute. Look for a non-abrasive chemical citrus cleaner that’s meant to break apart adhesive materials. Put the adhesive remover in a spray bottle and apply it to any adhesive you find. Leave the adhesive remover on the residue for 1 minute so it has time to soak in.[8]
    • Adhesive remover can be purchased from your local hardware store.
    • If you don’t have a spray bottle, you can also wet a cloth with the adhesive remover and apply it to the vehicle.
  2. 2
    Wipe the adhesive away with a cleaning cloth. Use a clean rag when you’re cleaning the residue off your vehicle. Work in a back and forth motion, applying firm pressure to the area to ensure you remove all of the adhesive. When you’re finished, the surface should feel smooth rather than sticky to the touch.[9]

    Tip: If the cloth doesn’t lift the adhesive, try scratching it off using a plastic scraper or squeegee.

  3. 3
    Clean the remover off your vehicle with soapy water or rubbing alcohol. Adhesive removers can leave a cloudy residue on your vehicle. Use a cloth soaked in soapy water or rubbing alcohol and wipe the area you just cleaned until no streaks are visible.[10]
    • If you're cleaning the adhesive off of a window, you can also use a standard glass cleaner.
  4. Advertisement

Community Q&A

  • Question
    What if the wrap has been damaged and just roughed all over?
    Robert Romero Jr
    Robert Romero Jr
    Community Answer
    You may still take the vinyl off as directed in the steps above. But instead, use gloves that have a latex coating on them—for two reasons: 1. for protection and 2. for gripping the vinyl better.
Advertisement

Warnings

  • Don’t let the wrap get warmer than 125 °F (52 °C) or else the adhesive will stick to your vehicle. Use a laser thermometer to check the surface temperature of the wrap if needed.
    ⧼thumbs_response⧽
Advertisement

Things You’ll Need

  • Plastic scraper
  • Heat gun
  • Chemical adhesive remover
  • Spray bottle
  • Cleaning cloth
  • Soap
  • Rubbing alcohol

About This Article

Hunter Rising
Co-authored by:
wikiHow Staff Writer
This article was co-authored by wikiHow staff writer, Hunter Rising. Hunter Rising is a wikiHow Staff Writer based in Los Angeles. He has more than three years of experience writing for and working with wikiHow. Hunter holds a BFA in Entertainment Design from the University of Wisconsin - Stout and a Minor in English Writing. This article has been viewed 40,113 times.
30 votes - 82%
Co-authors: 2
Updated: August 17, 2019
Views: 40,113
Categories: Cars
Advertisement