Having a treadmill at home is a great way to exercise without having to go to the gym. While treadmills are relatively easy to maintain, they do require some attention and regular cleaning.[1] To keep your treadmill operating correctly, we'll show you how to clean the surface, lubricate and maintain the treadmill’s deck and belt as needed, and protect the machine with a mat and surge protector.

Method 1
Method 1 of 4:

Caring for the Belt and Deck

  1. 1
    Lubricate the deck every 150 miles so the belt won’t wear out. Use an Allen wrench to loosen the bolts in the back of the treadmill by turning them counter-clockwise. This will loosen the belt so you can lift under it.[2] Then, lift the belt and apply 1 ounce (28 g) of silicone lubricant spray, liquid, or wax to the top of the running deck.[3] This will keep the belt from causing too much friction as you walk or run.[4]
    • Some treadmills are self-lubricating and don’t need to be sprayed or waxed. Make sure you check your owner’s manual before applying a lubricant.[5]
    • While it’s rare, some brands require a specific type of wax or spray. Check your owner’s manual to make sure you use the right type of lubricant.[6]
    • Make sure you don’t spray the lubricant on top of the belt, as it can make the belt slippery.[7]
  2. 2
    Tighten the belt as needed to maintain the tension. If the belt on your treadmill feels like it’s wiggling around too much, it’s likely that the belt has stretched a bit and needs to be tightened.[8] On most machines, there are 2 bolts at the end of the deck that you can tighten with an Allen wrench by adjusting the bolts clockwise.[9]
    • There is no set amount of time after which you’ll need to tighten the belt. Instead, do this as needed whenever you feel like the belt is wiggling or sliding and making it more difficult to use the machine.
    Advertisement
  3. 3
    Align the belt if it doesn’t run straight down the deck. In addition to stretching, the belt on your treadmill may slide off the center of the deck over time. On most machines, you can easily realign the belt by adjusting the bolts located on either side of the back of the machine. To do this, use an Allen wrench to adjust the bolts clockwise or counter-clockwise (depending on how the belt needs to be aligned) until the belt aligns in the center of the deck again.[10]
    • Because every machine is different, making sure that you check the owner’s manual to see how to align the belt on your particular treadmill.
    • Realigning the belt will not only make it easier to run, it will keep one side of the belt from wearing down faster than the other.
  4. Advertisement
Method 2
Method 2 of 4:

Cleaning Your Treadmill

  1. 1
    Wipe down your treadmill with a wet cloth after every use. Each time you use your treadmill, wipe down all the surface areas with a wet cloth or sanitizing wipe. While you may not be able to see it, your treadmill’s handles, belt, and screen likely get covered with sweat each time you run or power walk, which can cause the machine’s surface areas to corrode.[11]
    • Wiping down the surface areas on the machine will also help kill germs. Therefore, this is particularly important if you share your treadmill with anyone else.
    EXPERT TIP
    Greg Maurer

    Greg Maurer

    Health & Fitness Specialist
    Greg Maurer is a Health & Fitness Specialist and the Vice President of Fitness and Education for Workout Anytime. With over a decade of experience, he specializes in functional training, yoga, pilates, exercise and aging, home exercise programs, and numerous fitness diets. Greg holds a BS in Exercise Physiology from Temple University.
    Greg Maurer
    Greg Maurer
    Health & Fitness Specialist

    The treadmill gets dirty pretty quickly, particularly where you can't see it. This isn't an immediate problem, but it can be bothersome long-term. In addition to wiping it down, clean underneath it with a vacuum as regularly as possible. From time to time, you should also take the hood off the motor to clean it on the inside.

  2. 2
    Clean the area under the treadmill whenever you vacuum.[12] One of the most common reasons treadmills start to wear down is the accumulation of dirt and dust. To help keep the inside of your treadmill clear, vacuum the flooring under and within several feet around the treadmill about once per week, or whenever you vacuum the area.[13]
    • If your treadmill is too heavy to lift up so you can vacuum underneath, use your vacuum’s hose attachment and stick it underneath to suck up as much dirt and dust as you can.
  3. 3
    Vacuum inside the treadmill monthly to remove dust.[14] First, unplug your treadmill from the wall. Use a screwdriver to remove the screws that hold the hood in place, then follow the owner’s manual instructions to remove the hood off the treadmill’s motor.[15] Then, use the hose attachment on your vacuum to remove any dirt and dust from around the motor. Finally, stick the vacuum hose under the belt to vacuum the deck of the treadmill.[16]
    • The hood of the treadmill is generally located on the bottom of the front of the machine, directly under the machine’s screen. The deck of the treadmill is the floor of the machine underneath the moving belt.
    • Even if you’re diligent about cleaning the area under and around your treadmill, there will still likely be some dust build up.
    • Cleaning the motor will keep it running at its maximum efficiency, while cleaning the deck will help reduce friction that can break down the belt over time. 
  4. Advertisement
Method 3
Method 3 of 4:

Protecting Your Treadmill

  1. 1
    Use the treadmill on a level surface to keep the belt aligned. Perhaps the easiest way to protect your treadmill and keep it running smoothly is to set it up on an even surface. This will help keep the belt aligned and produce less friction, keeping the belt and deck from wearing down too quickly.[17]
    • If you want to be sure that your treadmill is on a level surface, lay a level across the belt. This will let you know whether your floors are even or not so you can adjust the treadmill’s position accordingly.
  2. 2
    Plug your treadmill into an outlet with a surge protector. If you leave your treadmill plugged in when you’re not using it, you can help protect the electronics in the machine by plugging it into a surge-protected outlet. This will keep your treadmill’s electronics safe during unexpected power surges and outages.[18]
    • You can also unplug your treadmill when you’re not using it to protect the machine’s computer.
  3. 3
    Invest in a treadmill mat to minimize vibrations. Placing a treadmill mat underneath the machine will not only help protect it from dust and dirt, it will also minimize vibrations that can make the belt and deck wear down faster. In addition, using a mat will also decrease the noise the machine makes when you’re using it.[19]
    • Treadmill mats also help protect the floor underneath your treadmill. 
    • Treadmill mats cost as little as $15 USD and can be purchased online and at most fitness equipment stores.
  4. Advertisement
Method 4
Method 4 of 4:

Addressing Common Treadmill Problems

  1. 1
    Observe the belt while it’s moving if your treadmill’s speed is erratic. If the speed on your treadmill is erratic, try turning on the machine to run at a slow speed and observe the belt to see if it’s hitching. Even if you’re diligent about maintaining your treadmill, the belt will inevitably wear down over time. If you notice that the speed on your treadmill starts to vary without you changing the setting, it’s likely that the belt is hitching and needs to be replaced.[20]
    • In most cases, you’ll be able to purchase a new belt from the store where you purchased your machine, or search online for a new belt for the same make and model.
    • If you don’t see any issues with the belt when you observe it, the erratic speed may be caused by a problem with the motor. If this is the case, you’ll need a repair technician to determine if it can be fixed.
  2. 2
    Unplug your treadmill if there’s a burning smell. If you’re using your treadmill and you start experiencing a burning smell, immediately stop using your treadmill, turn it off, and unplug it from the wall.[21] Whether it’s caused by dust in the motor, an object lodged under the belt, or a short circuit, burning smells generally indicate a problem that could become a fire hazard if you ignore it for too long.
    • If the burning smell is caused by dust, you can fix it by vacuuming the motor.
    • If the smell is caused by an object under the belt, removing the object will reduce the friction and get rid of the smell.
    • If your treadmill is short circuiting, you’ll need to get a professional to address the issue.
  3. 3
    Check the power cords if the console display isn’t working. If your treadmill belt is moving fine but the console display is blank, there is usually a minor issue with the power cords or batteries. First, check the power cords to see if any are old, crimped, or otherwise damaged and need to be replaced. If the power cords and wires are all in good shape, try unplugging the main power cord from the outlet for 1 minute to allow the circuit breaker to reset. Then, plug it back in to see if the display returns.[22]
    • If any cords or wires need to be replaced, you’ll likely be able to purchase a replacement at a hardware store or from the treadmill supplier.
  4. Advertisement

Expert Q&A

  • Question
    Can I lubricate my treadmill?
    Greg Maurer
    Greg Maurer
    Health & Fitness Specialist
    Greg Maurer is a Health & Fitness Specialist and the Vice President of Fitness and Education for Workout Anytime. With over a decade of experience, he specializes in functional training, yoga, pilates, exercise and aging, home exercise programs, and numerous fitness diets. Greg holds a BS in Exercise Physiology from Temple University.
    Greg Maurer
    Health & Fitness Specialist
    Expert Answer
    You should lubricate your treadmill on a regular basis. Depending on the make of the equipment, though, you might need to hire someone to do it for you, as the process can be complex.
  • Question
    Is it okay to leave your treadmill in an inclined position when not in use?
    Community Answer
    Community Answer
    Yes.
  • Question
    Will running or walking on the treadmill without athletic shoes ruin the treadmill?
    Community Answer
    Community Answer
    No, it won't ruin the treadmill, but it may be less comfortable for you.
Advertisement

About This Article

Greg Maurer
Co-authored by:
Health & Fitness Specialist
This article was co-authored by Greg Maurer. Greg Maurer is a Health & Fitness Specialist and the Vice President of Fitness and Education for Workout Anytime. With over a decade of experience, he specializes in functional training, yoga, pilates, exercise and aging, home exercise programs, and numerous fitness diets. Greg holds a BS in Exercise Physiology from Temple University. This article has been viewed 238,244 times.
4 votes - 100%
Co-authors: 22
Updated: November 18, 2022
Views: 238,244
Categories: Personal Fitness
Article SummaryX

To keep your treadmill maintained, you’ll need to clean it and lubricate the deck and belt as needed. After each use, wipe down your treadmill with a wet cloth or sanitizing wipe to remove any sweat. You should also vacuum around and underneath your treadmill at least once a month since dust and dirt can build up and wear down the machine. Every 150 miles or so, you should lubricate the deck. To do this, you’ll need to use an Allen wrench to loosen the bolts in the back of the treadmill, lift the belt, and apply silicone lubricant spray to the top of the running deck. This will prevent the belt from causing too much friction when you run. To keep your treadmill working well in the long run, make sure to place it on a totally level surface, which will help the belt stay aligned. Additionally, you should plug it into an outlet with a surge protector, which will keep it safe during power outages. To learn how to troubleshoot problems with your treadmill, read on!

Did this summary help you?
Advertisement