How to Fix an Off Track Window

Co-authored by Duston Maynes

Last Updated: May 21, 2022 References

If your car window is misaligned or stuck, but the hand crank or electric motor appears to be working fine, you may be dealing with an off track window.^{[1]
X
Expert Source

Duston Maynes
Automotive Repair Specialist
Expert Interview. 11 June 2021.} Though never fun, off track windows are a common automotive problem and can be easily fixed at home.

Part 1

Part 1 of 3:

Removing the Car Door Panel

1
Remove screws and bolts along the interior of the car door. Before fixing the window, you’ll need to get access to the inside of the car door. For smaller problems like an off track window, you can do this by removing the interior car door panel, the plastic cover concealing the car’s window mechanisms. These are typically held in place by simple screws and bolts, meaning you can remove them using a screwdriver and wrench. If the fasteners are particularly tight, use a power tool instead of a manual one.^{[2]
X
Research source}
- For doors with standard panel fasteners, look for screws along the top, base, and side of the panel.
- For doors where the fasteners are hidden or non-standard, check your owner’s manual for diagrams and removal instructions.
2
Remove the crank handle, control switch, and other accessories if necessary. Depending on the make and model of your car, you may also need to remove a crank handle, window control switch, or any number of accessories including cupholders, arm rests, luggage bins, and door handles. Most of these can be taken off with the same tools as the door itself, though some may require a specific tool or non-standard method of removal. Check your user’s manual for details on car specific accessories.^{[3]
X
Research source}

Advertisement
3
Pop the door panel off using a thin, sturdy tool. With all the trims and fastenings removed, place a small, strong tool under the edges of the door. Press down on the tool gently to pop the door panel out. You may need to do this in multiple spots around the panel to fully remove it.^{[4]
X
Research source}
- Though any thin tool can be used, ranging from small crowbars to thin pieces of metal, specialty panel removal tools will make the job easier.
4
Remove coverings and unplug any wires connected to the door panel. If your car has any, pull back insulation or vapor barriers covering the inside of the door. Then, unplug any wiring keeping the panel fixed to the car. When you’re finished, remove the door panel and put it to the side.^{[5]
X
Research source}

Part 2

Part 2 of 3:

Inspecting the Window Parts

1
Examine the window track for wear. In some cases, an off track window may be caused by a broken or worn out track. If areas in the track are rusted, apply a few drops of white lithium lubricant to them. If areas in the track are bent, try pressing them into shape using the back of a hammer, wrench, or other firm tool. If the track is rusted or bent to the point of being unusable, you will need to replace the window regulator and, most likely, the window motor.^{[6]
X
Research source}
- Depending on your car’s make and model, replacement regulators typically cost between $190 and $270, not including a motor.
2
Add adhesive if your window track is dry or rough. If your window track uses glue to hold the glass in place, touch it to make sure it is still sticky. If the window track is dry, rough, or cracked, squeeze a layer of Automotive Goop or similar automotive adhesive into it.^{[7]
X
Research source}
3
Inspect the electric window motor with a voltmeter. Over time, a bad window motor can cause the glass pane to stop moving, making it appear off track or causing it to fall out of alignment. Check the motor for any clear signs of damage, like dents or holes. If the device seems good, connect voltmeter wires to the motor’s connector terminals. If the voltmeter reads between +12 and -12 volts, the window motor is in good working condition. ^{[8]
X
Research source}
- If the motor seems fine but doesn’t operate correctly, replace the associated fuse in the fuse box. If it still doesn’t work, check the window control switch by connecting an ohmmeter to it and looking for little to no resistance when the switch is pressed.^{[9]
  X
  Research source}
- Depending on your car’s make and model, expect replacement motors to cost between $120 and $240, not including a regulator.
4
Check for bad wire connections. In some cases, a stuck or off-track window may have been caused by a loose or faulty wire. Examine each wire inside the door for kinks, tears, and other forms of damage. If they look good, make sure they’re fully connected to the window motor. If the wires are damaged or broken, you will need to replace them or, in some cases, the whole motor.^{[10]
X
Research source}
- Though not always available, model-specific replacement wires generally run between $15 and $50 dollars.

Part 3

Part 3 of 3:

Realigning the Glass

1
Drop the window glass to the bottom of the window channel. Since you will be realigning the glass, move it to the bottom of the frame that lines the inside of the car door, better known as the window channel. Using one hand, firmly slide the glass down as far as you can. If necessary, guide the bottom edge with your other hand.^{[11]
X
Research source}
- If the window is stuck, run a thin utility knife between the window and door to remove any blockage, then continue sliding it down. Keep the blade parallel to the window to avoid scratching it.
- If the window will not move down, pull the panel out through the top opening and reinsert it.
2
Move the glass onto the window track. Move your window glass until it is lined up on the window track again. Look for areas where the track is pinched, pressed down, or blocked and adjust the window accordingly. When you’re finished, your window should sit entirely within the track. Window tracks are not uniform, so consult your owner’s manual for model specific instructions.^{[12]
X
Research source}
- In some cars, you may need to remove the bolts on the window track, slide the window in, and rebolt the track.
3
Connect your glass to the window lift if necessary. Realigning your glass to fit the track may throw other parts of the window off, in particular the motor and other elements of the window regulator mechanism. Check to make sure that your window is connected to every part of the lift it needs to be, consulting your owner’s manual for model specific information. If anything is not properly connected, gently adjust your glass or the lift itself to fix the problem.^{[13]
X
Research source}
4
Cover your rollers and tracks with lubricant. Over time, your rollers and tracks will dry out, making it harder for them to raise and lower the window. To fix this, clear the rollers and tracks of any dirt or dust using a brush or can of compressed air, then rub on a coat of Lucas Oil white lithium grease or similar white lithium lubricant. Avoid generic brand lubricant like WD-40 unless you’re using a specialty variant.^{[14]
X
Research source}
5
Test to make sure the window works. If possible, reattach just the crank handle or control switch and use them to test the repair. For some cars, you may need to reattach the entire door panel before testing.
6
Reattach the door panel. When you’re finished checking and realigning your window, replace the door panel and everything you removed. Start by plugging in any wires you disconnected and replacing any protective covers. Then, slip your panel back in place followed by any accessories you removed. Finally, secure everything with the screws and bolts you took out.

Expert Q&A

Question

How can you tell if a window is off track?

Duston Maynes
Automotive Repair Specialist
Duston Maynes is an Automotive Repair Specialist at RepairSmith. Duston specializes in leading a team that handles a variety of automotive repairs including replacing spark plugs, front and rear brake pads, fuel pumps, car batteries, alternators, timing belts, and starter motors. Duston holds an Associate’s degree in Automotive/Diesel Technology from The Universal Technical Institute of Arizona and is a Certified Diagnostic Technician and Automobile Mechanics Technician through BMW STEP. RepairSmith received The 2020 Big Innovation Award by Business Intelligence Group and The Startup of the Year by the American Business Awards. RepairSmith was also included in Built in LA’s 50 Startups to Watch and The Business Intelligence Group’s 52 Names Leading the Way in Customer Service. RepairSmith offers in-home services to provide car owners convenient and complete auto repair everywhere.

Duston Maynes

Automotive Repair Specialist

Expert Answer

The window won't go up or down evenly. Sometimes, the window won't move and you can hear the regulator going.
Question

How do I align the window track in the front driver side window on a 2007 Pontiac Vibe?

Ryan Bacigalupi

Community Answer

The door will need to be disassembled and the glass removed. Once removed, the retainer should be located. The glass will need to be cleaned of all residual silicone and a new retainer and silicone will need to be applied.
Question

Is there a video showing how to do this?

Community Answer

Yes, there are videos on YouTube. Do a search for "how to replace a passenger side window." The process is the same.

Warnings

When working, wear a long-sleeved shirt, full pants, closed toed shoes, and a pair of latex or nitrile gloves for safety. Work slowly to avoid injuries from the glass or individual auto parts.

⧼thumbs_response⧽
Helpful 2 Not Helpful 1
The information in this article is intended to provide general answers for frequently asked questions about this topic, and may not be applicable to all vehicles. Please refer to your vehicle’s owner’s manual for details about maintenance intervals and other vehicle specifications. If you are unsure about your ability to perform any repair, we recommend contacting a certified automotive technician to perform the necessary work.

⧼thumbs_response⧽
Helpful 1 Not Helpful 0