How to Fix a Leaky Sink Drain Pipe

It’s always such a pain when you discover a leaky or broken pipe on your sink’s drain. When you find a leak, it usually means your pipes are loose, damaged, or worn out. Luckily, repairing your drain and pipes are really easy fixes you can do at home with a few supplies. If the leak drips from the pipes, then it might be loose connections or damage. If the leak comes from the base of your sink, then the sink strainer might be the culprit. We’ll start with some quick and temporary fixes to stop any leak right away, and then cover more permanent solutions depending on where you found the leak!

This article is based on an interview with our award-winning professional plumber, David Balkan, CEO of Balkan Sewer and Water Main Service. Check out the full interview here.

Method 1
Method 1 of 4:

Patching Leaks Temporarily

  1. Image titled Fix a Leaky Sink Drain Pipe Step 1
    1
    Apply a 2-part epoxy putty for the most durable temporary fix. A 2-part epoxy putty is made up of a base and a hardener that solidify around your pipe when they’re mixed together. Just knead both putties in your hand until they’re thoroughly combined. Then, press the putty onto the section of pipe that’s leaking so it’s about 1⁄2 inch (1.3 cm) thick. Leave the putty to cure for the amount of time listed on the packaging before running water through your drain again.[1]
    • You can buy 2-part epoxy putty from your local hardware store. You can use it on any type of pipe.
    • Even if the putty stops your leak, look for a more permanent solution to the leak as soon as you can.
  2. Image titled Fix a Leaky Sink Drain Pipe Step 2
    2
    Wrap self-securing silicone tape around the pipe if there’s only a minor leak. Silicone tape works best around the joints in your drain pipe since it’s meant for low-flow leaks. Pull the tape tight and wrap it around the pipe, overlapping half of the piece underneath it with each rotation. Keep wrapping your tape past the edges of the leak so it forms a tight seal.[2]
    • Silicone tape won’t stick directly to your pipe, but it will stick to itself, so it’s easy to remove later on. It also works on any type of pipe so it’s pretty versatile.
    Advertisement
  3. Image titled Fix a Leaky Sink Drain Pipe Step 3
    3
    Secure a pipe clamp over a leak if it’s in the middle of a pipe. Clamps have a flat rubber piece called a gasket and a metal fastener that attaches around the pipe. Just be sure to get a clamp that fits the size of your pipe so it has a tight seal. Press the gasket tightly against the section of pipe that’s leaking. Set the clamp on top of the gasket and secure it around the pipe. Then, use a wrench to tighten the clamp completely so water can’t escape.[3]
    • Clamps work for any type of pipe you’re repairing.
    • You cannot use clamps on joints or corners since they won’t sit properly around your pipe.
    4. Advertisement
Method 2
Method 2 of 4:

Fixing Leaky Pipe Connections

  1. Image titled Fix a Leaky Sink Drain Pipe Step 4
    1
    Tighten the slip nuts between pipes if they’re leaking at the joint. A lot of times, you may just have a loose slip nut, which is a round fastener where one pipe meets another. Go underneath your sink and find the first slip nut where the vertical pipe connects to the drain. Turn the slipnut counter-clockwise until it’s hand-tight. Work your way down the rest of the pipe tightening all of the other nuts.[4]
  2. Image titled Fix a Leaky Sink Drain Pipe Step 5
    2
    Replace rubber gaskets at pipe connections if they’re old and cracked. The gaskets are the small rubber pieces that fit between metal or PVC pipes and form a water-tight seal. Unscrew the slip nuts along the drain pipe and pull out the rubber gaskets to see if they have cracks or damage. If you notice any damage, replace the gaskets with ones that are the same size. Most gaskets will have a wider end and a narrower end. Push the narrow end of the gasket inside the pipe.[6]
    • If you’re replacing the rubber gaskets on a slip nut, you’ll slide the gasket directly onto the pipe instead. Make sure the narrower end of the gasket points toward the end of the pipe where you’re making the connection.
    • You can buy replacement gaskets in the plumbing section of your local hardware store.
  3. Image titled Fix a Leaky Sink Drain Pipe Step 6
    3
    Wrap plumber’s tape around threadings on metal pipes. Plumber’s tape, or Teflon tape, creates a water-tight seal where the pipes screw together. If you have metal drain pipes, unscrew the slip nuts holding them together. Wrap the plumber’s tape clockwise around the threading, overlapping each rotation by half of the tape’s width. Work up to the ends of the threading before cutting the tape and screwing your drain back together.[7]
    • Avoid putting the tape on counter-clockwise since it could bunch up or unravel when you screw the pipe back onto your drain.
    • Do not use plumber’s tape on PVC or plastic pipes since it could cause you to overtighten or damage the pipes.
    4. Advertisement
Method 3
Method 3 of 4:

Replacing the P-Trap

  1. Image titled Fix a Leaky Sink Drain Pipe Step 7
    1
    Put a bucket or pan underneath the pipes. Even though there’s no running water in your drain pipe, residual water may get caught in the P-trap, which is the J-shaped piece of pipe underneath your sink. Clear out the space underneath your drain pipes and set a tray or bucket directly under your pipes.[8]
    • Some P-traps have a screw-off valve on the bottom you can use to drain it. Just turn the valve on the P-trap counter-clockwise until water spills out.
  2. Image titled Fix a Leaky Sink Drain Pipe Step 8
    2
    Unscrew the slipnuts starting from the drain to remove the pipe. The slipnuts are the round connectors between 2 pipes. Start with the slip nut where your sink drain connects to the long vertical pipe underneath your sink. Turn the nut clockwise to loosen it completely. Follow the pipe and unscrew any remaining slipnuts until you reach the horizontal pipe coming out from your wall. Each section of pipe should easily detach as soon as you unscrew the slipnuts attached to it.[9]
    • If only the J-shaped section of the P-trap is damaged, then you only need to remove the slipnuts connecting to that portion of pipe. You can leave the other pipes connected to your drain and wall.[10]
    • Make sure no one uses your sink after you detach any drain pipes, or else water will spill onto the floor. If you want to, you can turn off the water supply directly at your sink to make sure no one uses it. Find the supply valve connected to the wall and turn it clockwise to shut it off.[11]
  3. Image titled Fix a Leaky Sink Drain Pipe Step 9
    3
    Buy a P-trap that’s the same size as your old one. Bring your P-trap and any other drain pipes you removed with you to the hardware store. Your new P-trap kit will come with the pipes, gaskets, and slipnuts you need to install it. Make sure the new kit you buy has a P-trap and pipes that are exactly the same size as your old ones, or else they won’t properly fit. [12]
    • Many P-trap kits are made from PVC so they’re easy to install and take apart, but you can also buy metal drain kits.
  4. Image titled Fix a Leaky Sink Drain Pipe Step 10
    4
    Screw the new vertical pipe onto the bottom of the drain. Use the longest section of pipe to connect to your drain. Hold the top of the pipe against the bottom of your sink’s drain and slide the slip nut onto the drain’s threading. Just turn the slipnut counter-clockwise to tighten it onto your drain.[13]
    • The pipe may come with a flanged washer, which is a round rubber piece that fits inside the end of the pipe. If your P-trap kit has one, place the narrow end of the washer inside the drain pipe.
  5. Image titled Fix a Leaky Sink Drain Pipe Step 11
    5
    Attach the trap arm and washer to the stub out in your wall. The trap arm is a short piece of pipe that has a right angle, and it extends out from your wall. Push the wider end of a flanged washer onto the straight end of the trap arm. Then, slide the trap arm into the drain pipe sticking out from your wall so it makes a tight seal with the washer. After that, just tighten the slipnut to secure the trap arm in place.[14]
  6. Image titled Fix a Leaky Sink Drain Pipe Step 12
    6
    Install the new P-trap on the pipes. Slide the slipnuts and flanged washers onto the trap arm and the vertical drain pipe. Make sure the narrow ends of the washers point toward the open ends of the pipe. Position the P-trap on the ends of the pipes, and screw on the slipnuts until they’re both hand-tight.[15]
    • You do not need to use any sealant or pipe glue on a P-trap since you’ll want to be able to take it apart later on.
  7. Image titled Fix a Leaky Sink Drain Pipe Step 13
    7
    Test the trap for any leaks. Turn on your faucet and let the water run down your sink’s drain. Watch your pipes and the connections to make sure that there isn’t any water dripping out. If there is, then try giving your slipnuts a quarter-turn counter-clockwise with a pair of pliers to tighten them.[16]
    • If you notice your leak comes from where your drain connects to your sink, then you may need to replace the strainer instead.
    8. Advertisement
Method 4
Method 4 of 4:

Replacing the Sink Strainer

  1. Image titled Fix a Leaky Sink Drain Pipe Step 14
    1
    Disconnect the drain pipe from the bottom of the sink strainer. Your sink strainer prevents food from getting into your pipes and it’s where water drains out of your sink. Go underneath your sink and find the round slipnut between the vertical drain pipe to the bottom of the sink strainer.[17] You should be able to easily loosen the slipnut by hand just by turning it counter-clockwise.[18]
    • If you have trouble getting the slipnut loose, then use a pair of pliers to get it moving.
  2. Image titled Fix a Leaky Sink Drain Pipe Step 15
    2
    Loosen the strainer’s locknut and remove it from your sink. The locknut is a large hexagonal metal or plastic fastener holding your sink strainer against the bottom of your sink. Grip the locknut with a pair of channel locking pliers so you get the best grip.[19] Turn the locknut clockwise to loosen it. Keep unscrewing the locknut until it drops away from your sink. After that, just grab and pull the strainer straight out from the top of your sink.[20]
    • Some strainers have screws holding them in place. If that’s the case, then use a screwdriver instead.
  3. Image titled Fix a Leaky Sink Drain Pipe Step 16
    3
    Buy a new sink strainer that matches the size of your old one. There are a few different kinds of sink strainers, so bring the old one with you to the hardware store so you know what to get. Try to get one that’s the same style and size as the old one so you’re less likely to run into any problems.[21]
    • Bell washer sink strainers have a large bell-shaped piece that connects underneath your sink.
    • Locknut strainers have a large threaded nut that holds them in place to prevent leaks.
  4. Image titled Fix a Leaky Sink Drain Pipe Step 17
    4
    Wipe the drain hole clean with paper towels. There’s probably some leftover putty from the last installation or built-up gunk around the rim of the drain hole. Take a wet paper towel and gently wipe the area around the hole so you have a clean work surface.[22]
  5. Image titled Fix a Leaky Sink Drain Pipe Step 18
    5
    Apply a rope of plumber’s putty around the drain hole. Plumber’s putty is a non-adhesive substance that creates a water-tight seal around drains. Scoop out a handful of plumber's putty and knead it together so it’s easy to work with. Roll the putty between your palms to make a long rope that’s about 1⁄2 inch (1.3 cm) thick. Set the plumber’s putty around the rim of the drain hole.[23]
    • You can buy plumber’s putty from your local hardware store.
  6. Image titled Fix a Leaky Sink Drain Pipe Step 19
    6
    Push the new strainer into the hole in the top of your sink. Separate the top and bottom halves of the strainer if it has multiple pieces. Align the top piece of the strainer with the hole and push it down into the putty firmly. Try to center the drain in the hole so there aren’t any gaps between it and the sink.[24]
    • It’s okay if the extra putty presses out from the sides of the sink strainer. Just wipe it off and throw it away.
  7. Image titled Fix a Leaky Sink Drain Pipe Step 20
    7
    Tighten the locknut onto the bottom of the sink strainer. Stick a pair of needlenose pliers into the strainer’s opening from the top and hold them firmly in place to keep the strainer from moving.[25] Screw the locknut clockwise by hand until it’s tight. Then, use a pair of channel-locking pliers to spin the locknut by another quarter turn.[26]
    • If you don’t hold the sink strainer in place, it will spin in the wet putty and won’t properly seal.
    • Be careful not to overtighten your strainer so you don’t damage it or your sink.
  8. Image titled Fix a Leaky Sink Drain Pipe Step 21
    8
    Screw the drain pipe to the bottom of the strainer. Realign the slipnut on the vertical drain pipe with the bottom of the sink strainer. Then, turn it counter-clockwise to tighten it against the drain. Keep turning the nut until it’s hand-tight.[27]
  9. Image titled Fix a Leaky Sink Drain Pipe Step 22
    9
    Run some water through the drain to check for leaks. Plug your sink and fill it up with a little bit of water from your faucet. Check underneath your sink to make sure there isn’t any water dripping underneath. Then, unplug your drain and let the water drain out. Watch your pipes to make sure there aren’t any leaks.[28]
    • If you still notice leaks, then call a plumber to look at your sink.
    10. Advertisement

Warnings

  • If you don’t feel comfortable working on the pipes yourself, contact a professional plumber to ensure your drain gets fixed properly.
    ⧼thumbs_response⧽
Advertisement

You Might Also Like

Bend a 3‐Point Saddle
How to
Bend a 3‐Point Saddle
Measure Pipe Size
How to
Measure Pipe Size
Fix Leaking Pipes
How to
Fix Leaking Pipes
Thread Pipe
How to
Thread Pipe
Repair PVCHow to Easily Patch and Repair PVC Pipe
Fix a Broken Pipe
How to
Fix a Broken Pipe
Hide Pipes
How to
Hide Pipes
Clear a Clogged Waste Pipe
How to
Clear a Clogged Waste Pipe
Clean a P‐Trap or U‐Bend
How to
Clean a P‐Trap or U‐Bend
Join PPR Pipe
How to
Join PPR Pipe
Bend Copper Tubing
How to
Bend Copper Tubing
Connect Pex to Copper
How to
Connect Pex to Copper
Cut Galvanized Pipe
How to
Cut Galvanized Pipe
Measure Bends when Bending Pipes
How to
Measure Bends when Bending Pipes
Advertisement

References

  1. ↑ https://youtu.be/OqFaUhs4pHg?t=54
  2. ↑ https://youtu.be/m3cfvLGiw8E?t=86
  3. ↑ https://youtu.be/m3cfvLGiw8E?t=113
  4. ↑ https://www.epa.gov/sites/default/files/2017-02/documents/ws-ourwater-detect-and-chase-down-leaks-checklist.pdf
  5. ↑ David Balkan. Professional Plumber & CEO of Balkan Sewer & Water Main. Expert Interview. 29 April 2021.
  6. ↑ https://youtu.be/HDWxn4kHzwY?t=321
  7. ↑ https://piperepair.co.uk/2020/07/13/how-to-use-plumbers-tape-your-guide-to-successful-thread-sealing/
  8. ↑ https://www.bobvila.com/articles/plumbing-repairs/
  9. ↑ https://www.bobvila.com/articles/plumbing-repairs/
  1. ↑ https://youtu.be/LOX4vNwLIIQ?t=90
  2. ↑ David Balkan. Professional Plumber & CEO of Balkan Sewer & Water Main. Expert Interview. 29 April 2021.
  3. ↑ https://youtu.be/2befOMjA3ho?t=34
  4. ↑ https://youtu.be/2befOMjA3ho?t=41
  5. ↑ https://youtu.be/2befOMjA3ho?t=68
  6. ↑ https://youtu.be/LOX4vNwLIIQ?t=121
  7. ↑ https://youtu.be/jvlI04X76Mo?t=283
  8. ↑ https://youtu.be/SKWtznSozNQ?t=104
  9. ↑ David Balkan. Professional Plumber & CEO of Balkan Sewer & Water Main. Expert Interview. 29 April 2021.
  10. ↑ David Balkan. Professional Plumber & CEO of Balkan Sewer & Water Main. Expert Interview. 29 April 2021.
  11. ↑ https://youtu.be/CaS6Y0XVQmE?t=61
  12. ↑ https://youtu.be/SKWtznSozNQ?t=280
  13. ↑ https://youtu.be/iQaDgfc-MYI?t=102
  14. ↑ https://youtu.be/HDWxn4kHzwY?t=229
  15. ↑ https://youtu.be/WNnQUHLsUCA?t=131
  16. ↑ https://youtu.be/WNnQUHLsUCA?t=139
  17. ↑ David Balkan. Professional Plumber & CEO of Balkan Sewer & Water Main. Expert Interview. 29 April 2021.
  18. ↑ https://youtu.be/Ls3HGF-xs9I?t=120
  19. ↑ https://youtu.be/HDWxn4kHzwY?t=368
  20. ↑ David Balkan. Professional Plumber & CEO of Balkan Sewer & Water Main. Expert Interview. 29 April 2021.

About This Article

David Balkan
Written by:
David Balkan
Professional Plumber & CEO of Balkan Sewer & Water Main
This article was written by David Balkan and by wikiHow staff writer, Hunter Rising. David Balkan is a Professional Plumber, CEO of Balkan Sewer and Water Main Service, and President of Balkan Sewer and Drain Cleaning. As a hands-on owner of these companies for over 40 years, David is knowledgeable about water service lines, sewers, and drain line issues. David is a Committee Chairman of the Master Plumbers Council and has sat on the Executive Committee of the Sub Surface Plumbers Association of New York for over 30 years. His knowledge and solution-oriented approach contributed to Balkan Sewer and Water Main Service being the largest and most trusted service in New York City and the recipient of the 2017 Angie’s List Super Service Award. This article has been viewed 76,574 times.
21 votes - 95%
Co-authors: 9
Updated: May 28, 2022
Views: 76,574
Categories: Piping
Advertisement