X
wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 9 people, some anonymous, worked to edit and improve it over time.
This article has been viewed 90,129 times.
Learn more...
A leaky faucet (tap) in your home can cost you money in water bills; a leaky outdoor faucet can not only cost you money, it can cause damage to your garden and grass in addition to your home itself. Fortunately, leaky faucets of any kind are usually caused by a worn-out washer. Replacing a worn-out washer is a simple process that takes very little time and only a few common tools.
Steps
-
1Locate the main water valve.[1]
-
2Turn off the water to your house.[2]Advertisement
-
3Locate the nut that sits just behind the faucet knob.
-
4Remove the nut using an adjustable wrench.[3]
-
5Pull the faucet handle straight out to remove the valve stem; it should be approximately 12 inches (30.5 cm) long.
-
6Remove the screw at the end of the long valve stem using a flat-head screwdriver.[4]
-
7Pry the old washer out carefully using a small screwdriver.[5]
-
8Find a new washer of the same size and shape.
-
9Clean the seat where the washer will go with a small soft brush or toothpick.
-
10Insert the new washer, ensuring a snug fit.
-
11Replace the screw on the end of the valve stem.[6]
-
12Grease the threads on the valve stem with some silicone to make the faucet turn on and off easier.[7]
-
13Replace the valve stem into the faucet pipe.
-
14Wrap the faucet threads with plumber's tape to ensure a snug fit.
-
15Reattach the faucet knob.
-
16Tighten the packing nut.
-
17Turn on the main water valve.
-
18Turn on the outside spigot.
-
19Let the water run for several minutes to clean out any debris that may have gotten inside the valve stem and spigot while working on them.[8]
-
20Shut off the spigot.
-
21Inspect the spigot to ensure that there are no leaks.
Advertisement
Community Q&A
-
QuestionHow can I remove the faucet if it will not come out?Community AnswerCut the faucet off the pipe and install a new faucet. You can solder on a new faucet or thread fitting. Alternatively, you can screw on a compression fitted valve to a plain pipe.
Advertisement
Warnings
- Use care and patience when reinstalling the valve stem. There are threads on both the valve stem and the inside pipe to which it attaches. These can be easily stripped or damaged if the parts are forced together in any way or are not seated correctly. You may need to adjust both the valve stem and packing nut at the same time to get the correct fit.⧼thumbs_response⧽
Advertisement
Things You'll Need
- Outdoor spigot
- 12-inch (30.5 cm) adjustable wrench
- Flat-head screwdriver
- Small screwdriver, flat head or other
- Pliers
- Washers of various sizes and shapes
- Plumber's tape
- Silicone grease
- Paper towels
- Container or shallow dish for loose parts
References
- ↑ https://www.wsscwater.com/customer-service/residential-tips/locating-and-operating-your-main.html
- ↑ https://www.wsscwater.com/customer-service/residential-tips/locating-and-operating-your-main.html
- ↑ https://todayshomeowner.com/video/stop-an-outdoor-faucet-from-dripping/
- ↑ https://todayshomeowner.com/video/stop-an-outdoor-faucet-from-dripping/
- ↑ https://todayshomeowner.com/video/how-to-repair-a-leaking-outdoor-faucet-hose-bib/
- ↑ https://todayshomeowner.com/video/how-to-repair-a-leaking-outdoor-faucet-hose-bib/
- ↑ https://www.visionaware.org/info/everyday-living/home-repairs/gils-guide-to-home-repairs/faucet-washer-replacement/1235#reassemble
- ↑ https://www.visionaware.org/info/everyday-living/home-repairs/gils-guide-to-home-repairs/faucet-washer-replacement/1235#reassemble
- http://www.familyhandyman.com/DIY-Projects/Home-Repair/Faucet-Repair/how-to-repair-a-noisy-outdoor-faucet
About This Article
Advertisement