X
wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 15 people, some anonymous, worked to edit and improve it over time.
This article has been viewed 72,448 times.
Learn more...
Hair sticks are a great way to secure long hair in a bun and can be made for almost no cost in materials. Just use twigs you find lying around in the yard.
Steps
-
1Work out your stick length. You do this by measuring the width of your bun and adding a couple of inches.
-
2Find your stick. Go for a walk and collect some twigs. They should be no thicker than your index finger. Your stick should to be at least two inches longer than what you need. Shaping will shorten the final stick.
- Don't worry about getting a perfectly straight stick. Slight bends and curves in the wood make it more interesting to look at and they will hold your hair more securely.
- Avoid evergreen woods like pine as they contain large amounts of sap.
Advertisement -
3Look for sticks that flex. Discard any sticks that snap easily. Hair is pretty strong. If a stick snaps when you bend it slightly, it will break in your hair.
-
4Clean your stick. Using a knife, remove the bark from your chosen stick.
-
5Cut off any prominent protrusions. Any big bumps will make it hard to slide the stick into your hair.
-
6Trim your stick. With a hacksaw, cut the stick to the desired length. Be sure to remove both ends.
-
7Shape the stick. Carve one end of the stick so it tapers into a blunt point.
-
8Round off the other end of the stick. This is where you hold the stick to insert into a bun.
-
9
-
10Detail your stick. Draw your desired design onto the stick with a pencil or ballpoint pen. Do not use an ink pen as ink may bleed into the wood.
-
11Carve out the design. Cut into the stick at a 45° angle just below the lines you have drawn.
-
12Continue to shape the design. Cut into the stick at a 45° angle above the lines to cut out a V shaped piece of wood.
-
13Carve out the entire design in this way. Work carefully to cut away only what you want.
Advertisement
-
1Sand the stick with medium sandpaper.
-
2Sand smooth all edges. Fold the sandpaper in half and use the edge to sand inside the cuts you made for the design.
-
3Repeat with fine sandpaper. Go over the stick with fine sandpaper, folding it again to sand the cuts.
-
4Polish the stick smooth. Use a nail buffer or progressively finer sandpaper to get the stick really smooth.
-
5Oil the stick. Put a small amount of your chosen oil on a plate. Use your fingers to apply it to the wood. Make sure all the wood is covered with oil.
- Walnut oil brings out darker colours in the wood. Wood that looked rather boring before, can look stunning after it has been oiled. The darker the colour, the bigger difference the walnut oil will make.
-
6Allow the stick to soak up the oil for a couple of hours.
-
7Remove any excess oil with tissue. Wipe until no oil comes off the stick.
Advertisement
Community Q&A
-
QuestionCan I paint the stick?Community AnswerOf course.
-
QuestionWhat kind of wood should I use?Community AnswerIt really doesn't matter. Oak is hard and pine is soft -- try whatever is in your area.
-
QuestionWhat is a hair stick?Community AnswerA hair stick is a sort of hair accessory, usually used to secure buns. It's a stick that you put in your hair.
Advertisement
Warnings
- Avoid walnut oil if you have a nut allergy or will be giving the stick to someone with a nut allergy.⧼thumbs_response⧽
- Always point the knife away from you when carving. Wear safety glasses.⧼thumbs_response⧽
Advertisement
Things You'll Need
- A twig
- A hacksaw
- A wood carving knife; if you don't have one, a penknife or craft knife will work
- Sandpaper in coarse, medium and fine
- Nail buffer or super fine sandpaper for polishing
- Walnut, linseed oil or grapeseed oil
About This Article
Advertisement