How to Adjust a Mesh Watch Strap

Co-authored by wikiHow Staff

Last Updated: September 16, 2021 References

Metal mesh watch straps are a popular option for both men’s and women’s watches. Although these watches operate a little differently from traditional leather- or metal-strap watches, you can easily adjust your mesh watch strap using a flathead screwdriver. Adjust the placement of the sliding clasp on the lower portion of the mesh band to fit the mesh strap comfortably around your wrist.

Part 1

Part 1 of 2:

Opening the Clasp

1
Find a small flathead screwdriver. You will need a small, pointed object to pry open the mesh clasp. The type of screwdriver used to adjust eyeglass screws would work well.^{[1]
X
Research source} A Phillips head screwdriver will not work, since it will be too large to fit into the clasp.
- If you do not have a small screwdriver, you could use a different small, blunt tool. For example, try one of the prying tools built into a Swiss Army knife.^{[2]
  X
  Research source}
- Do not use a knife blade. The point of the knife could slip and scratch the watch, or you could accidentally cut your fingers with the blade.
2
Hold the clasp steady. Place the watch flat on a table or other firm surface. Use your non-dominant hand to hold the clasp firmly in position.^{[3]
X
Research source}
- If you’re not near a table, it’s possible to adjust the clasp if you’re holding the watch in your hand. However, if this is your first time adjusting a mesh watch strap, doing it on a table will make the process easier.
Advertisement
3
Place the screwdriver head into the small hole on the clasp. The front side of the clasp (which will be facing up when the watch is laying face-up) will have a small hole about ¹⁄₄ inch (0.64 cm) wide directly in its center. You’ll use this hole to pry the strap open. Put the tip of your screwdriver—or other tool—directly into the hole.^{[4]
X
Research source}
- The hole will be shaped and sized differently depending on the brand of mesh strap you’re adjusting.
- Some clasps may even have a small arrow pointing to the hole.
4
Pry the clasp upwards to open it. There will be a small set of hinges at the base of the watch clasp, on the side closest to the watch’s face. Slowly exert pressure down on the screwdriver to pry the top portion of the clasp up and open.^{[5]
X
Research source}
- If the clasp doesn’t fully open with the use of the screwdriver, use your thumb and index finger to open it completely.

Part 2

Part 2 of 2:

Adjusting the Clasp

1
Slide the clasp up or down the mesh strap. Adjust the clasp to accommodate your wrist.^{[6]
X
Research source} Sliding the clasp farther up the mesh strap (towards the watch) will tighten the strap on your wrist, and sliding the clasp down the mesh strap (away from the watch) will loosen the strap.
- Be careful not to drop the clasp on the floor.
2
Align the back of the clasp with a groove in the mesh watch strap. Due to its design, the back of the mesh watch strap will have a small groove every ¹⁄₈ in (0.32 cm) or so. The back of the clasp will have a corresponding indentation that fits snugly into any of these grooves.^{[7]
X
Research source}
- If you try to close the clasp without first having aligned it with a slot in the mesh strap, the clasp will be unable to close.
3
Close the clasp. Once you’ve found the best position for the watch strap and aligned it with a groove in the mesh strap, close the clasp to lock it in place.^{[8]
X
Research source} You should hear a “pop” sound as the clasp snaps shut.
- At this point, the watch is ready to be worn.

Community Q&A

Question

What if there are not enough grooves on the strap?

Jessica Alcorn

Community Answer

The watch clasp can only be secured into these grooves, you may need to look into longer watch bands if they are available for your brand.